Goosky Legend S1 2.4G RC Electric 3D Helicopter User Manual

1. Introduction

Welcome to the user manual for your Goosky Legend S1 2.4G RC Electric 3D Helicopter. This manual provides essential information for the safe operation, setup, maintenance, and troubleshooting of your new model. Please read this manual thoroughly before operating the helicopter to ensure a safe and enjoyable experience.

Safety Warning:

• This product is recommended for users aged 16 and above.
• Always operate the helicopter in open, clear areas, away from people, animals, and obstacles.
• Never fly near power lines, roads, or water bodies.
• Ensure batteries are fully charged and properly installed before each flight.
• Always turn on the remote controller first, then the helicopter. Turn off the helicopter first, then the remote controller.
• Do not touch moving parts (rotors) during operation.
• Failure to follow safety guidelines may result in injury or property damage.

Figure 1: Goosky Legend S1 RC Helicopter and its packaging, indicating an age recommendation of 16+.

2. Package Contents

Upon opening the package, please verify that all the following items are included:

• Helicopter Kit (Goosky Legend S1) x 1
• Remote Controller x 1
• Receiver x 1
• 7.4V 300mAh High Voltage Battery x 2
• Charging Adapter x 1
• Bluetooth Module x 1
• Instruction Manual x 1 (this document)
• Assorted Screws

Figure 2: The Goosky Legend S1 helicopter, its remote controller, and two included batteries.

3. Setup

3.1 Battery Charging

1. Connect the provided charging adapter to a power source.
2. Connect the 7.4V 300mAh LiPo battery to the charging adapter.
3. Allow approximately 60 minutes for a full charge. The battery features overcharging, over-discharging, and low-battery indication functions to extend its service life.
4. Always supervise batteries during charging.

3.2 Remote Controller Preparation

1. Install the required batteries (not specified in JSON, assume standard AA/AAA) into the remote controller.
2. Ensure the remote controller is powered off before proceeding.

3.3 Initial Helicopter Inspection

• Inspect the carbon fiber frame fuselage structure for any damage.
• Verify that the main propeller clamps (7075 aluminum alloy) and BL aileron system blades (nylon + carbon fiber composite) are securely attached.
• The helicopter features a non-removable canopy with a quick-release battery design for ease of access.

3.4 Pairing the Remote Controller and Helicopter

1. Turn on the remote controller.
2. Connect the fully charged battery to the helicopter.
3. Place the helicopter on a flat, stable surface.
4. The remote controller and helicopter should automatically pair. Refer to the remote controller's specific manual for detailed pairing instructions if issues arise.

Figure 3: Key features for setup and operation, including mobile app parameter adjustment and quick battery removal.

4. Operating Instructions

The Goosky Legend S1 is equipped with a GTS control system and dual brushless direct-drive motors, designed for stable and precise flight, including advanced 3D aerobatics.

4.1 Basic Flight Controls

• Throttle: Controls the main rotor speed and altitude.
• Elevator (Pitch): Controls forward and backward movement.
• Aileron (Roll): Controls left and right sideways movement.
• Rudder (Yaw): Controls the tail rotor, allowing the helicopter to rotate left or right on its vertical axis.

Familiarize yourself with these controls in a safe, open environment before attempting advanced maneuvers.

4.2 Advanced 3D Aerobatics

The GTS control system supports all-round 3D violent aerobatics. This intelligent flight control system ensures stable, fast, and accurate flight, making it suitable for experienced pilots. Practice these maneuvers at a safe altitude and distance.

4.3 Mobile App Parameter Adjustment

Utilize the mobile application (via the Bluetooth module) to fine-tune flight parameters and customize your flying experience. Refer to the app's instructions for detailed guidance on adjustments.

Figure 4: The Goosky Legend S1, engineered for high-performance aerobatic flight with dual brushless direct drive.

5. Maintenance

5.1 Post-Flight Inspection

• Visually inspect the helicopter for any signs of damage, loose screws, or worn parts after each flight.
• Check the main rotor blades and tail rotor for cracks or chips. Replace damaged blades immediately.
• Ensure all linkages and servos are moving freely and without obstruction.

5.2 Battery Care and Storage

• Always allow batteries to cool down before recharging.
• Store LiPo batteries in a cool, dry place, away from direct sunlight and flammable materials.
• Do not store fully charged or fully discharged batteries for extended periods. Store them at a "storage charge" level (typically around 3.8V per cell).
• Dispose of damaged or swollen batteries according to local regulations.

5.3 Cleaning

Gently clean the helicopter with a soft, dry cloth. Avoid using solvents or harsh chemicals, as these can damage plastic and electronic components.

6. Troubleshooting

7. Specifications

Figure 5: Detailed product parameters and dimensions of the Goosky Legend S1 helicopter.

8. Warranty and Support

For warranty information, technical support, or replacement parts, please refer to the official Goosky website or contact your retailer. Keep your purchase receipt as proof of purchase for any warranty claims.

Manufacturer: YILQ