CO-Z Automatic Dual Swing Gate Opener Kit

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your CO-Z Automatic Dual Swing Gate Opener Kit. Designed for gates up to 1300 lb and 36 ft, this system offers convenience and security for residential driveways, commercial properties, and farm gates. Please read this manual thoroughly before installation and use to ensure proper function and safety.

Image: CO-Z Automatic Dual Swing Gate Opener Kit

2. Safety Information

• Always disconnect power before performing any service or maintenance.
• Ensure all electrical connections comply with local codes and regulations.
• Keep children and pets away from the gate area during operation.
• Do not attempt to repair or modify the gate opener yourself. Contact qualified personnel for service.
• Install infrared sensors to prevent the gate from closing on obstacles.
• Use manual release keys during power outages for safe gate operation.

3. Package Contents

Verify that all components are present and undamaged before beginning installation:

• 2 x Gate Actuators (Motors)
• 1 x Control Box with Casing
• 2 x Remote Controls
• 2 x Post Brackets
• 2 x Gate Brackets
• 2 x Post Pivot Brackets
• 1 x Wired Photocell (Infrared Sensor Set)
• 1 x Manual Release Key
• 1 x Limit Stop
• Actuator Tip Bolts, Actuator End Bolts, M8 Screws, M8 Nuts
• Instruction Manual

4. Installation

The following video provides a visual guide for the installation process. Please refer to the detailed steps below the video for specific instructions.

4.1 Post Bracket Installation

1. Unpack all parts and verify their sizes against your gate and post dimensions.
2. Attach two post brackets to one post pivot bracket using M8 screws. Repeat for the second set of brackets.
3. Secure the assembled post bracket to the gate post, ensuring it is level with the gate opener.
4. Attach the gate opener to the post bracket using the provided bolts.
5. Remove the rubber plug from the gate opener, unlock the motor, and extend the actuator to the front bracket.
6. Fix the front bracket to the gate opener and mount it in the predetermined spot on the gate.
7. Repeat these steps to install the second gate opener on the other gate leaf.

Image: Multi Mounting Positions for optimal installation flexibility.

4.2 Control Box Installation

1. Install the control box at a convenient height near the gate opener.
2. Pass the motor wires through the box and connect them to the terminals. Ensure correct polarity (+/-) for each gate direction. A dual-core extension may be required if wires are short.
3. Run the power cable through the hole in the control box and connect it to the transformer's terminal for power.
4. Power up the mainboard.

4.3 Infrared Sensors Installation

1. Open the receiver housing and connect 4 wires: V+, V-, COM, and NO.
2. The transmitter needs 2 wires.
3. Place the IR sensors in the desired location, ensuring the wire is long enough to reach the control box.
4. Connect the receiver's V+ to the 12V DC/24V DC terminal, V- and COM to the COM terminal, and NO to the PH terminal.
5. Connect the transmitter's V+ to the 12V DC/24V DC terminal and V- to the COM terminal.
6. Install the IR sensor housings securely.

Image: Infrared Sensors Equipped for obstacle detection.

4.4 Travel Setting

1. Move the gates to any position.
2. Press and hold the "+" button on the control board until the display shows "SU".
3. Your gates should close, stop, and fully open automatically.
4. After both arms open fully, the gate opener closes again to complete the learning process.
5. Lock the motor, replace the rubber plug, and reinstall the control box cover.

5. Operating Instructions

5.1 Remote Control Operation

Use the provided remote controls to open and close your gates. The kit includes 2 remotes and supports up to 32. Interfaces for HomeLink, Bluetooth, and Wi-Fi functionality are reserved for future updates.

Image: Remote Control

5.2 Customizable Closing Times

You can set personalized closing times of 15, 30, 60, or 90 seconds once the gates are open. Refer to the control box manual for specific programming instructions.

5.3 Pedestrian Mode

The system features a pedestrian mode for partial gate openings, allowing a single gate leaf to open for smooth pedestrian passage.

5.4 Dependable Safety Features

• Automatic Locking: The electric gate openers automatically lock your gates when closed to prevent unauthorized access.
• Infrared Sensors: If an obstacle is detected by the integrated infrared sensors, the gates will stop and reverse, preventing damage or injury.
• Manual Release: Included manual release keys serve as a reliable backup in case of a power outage, allowing manual operation of the gates.

6. Maintenance

• Regularly inspect the gate openers, brackets, and mounting hardware for any signs of wear, damage, or loose connections.
• Keep the gate path clear of debris and obstructions.
• Clean the infrared sensors periodically to ensure proper function.
• Lubricate moving parts as recommended by the manufacturer to ensure smooth operation and extend product life.

7. Troubleshooting

If you encounter issues with your gate opener, refer to the following common troubleshooting steps:

• Gate not opening/closing: Check power supply, remote control battery, and ensure no obstructions are blocking the gate path. Verify all wiring connections in the control box.
• Gate stops unexpectedly: Inspect infrared sensors for obstructions or misalignment. Check for any physical impediments to gate movement.
• Remote control not working: Replace remote battery. Ensure the remote is programmed correctly to the control box.
• Unusual noises: Inspect the gate hinges and opener arms for wear or damage. Lubricate moving parts if necessary.

For persistent issues, contact CO-Z customer support for assistance.

8. Specifications

9. Warranty and Support

CO-Z products are designed for durability and performance. For warranty information, technical support, or to purchase replacement parts, please visit the official CO-Z website or contact their customer service department. Keep your purchase receipt for warranty claims.