Introduction
The ANYCUBIC Wash and Cure 3 is an advanced 2-in-1 station designed to streamline the post-processing of resin 3D prints. It combines washing and curing functionalities into a single unit, offering enhanced efficiency and convenience for users of LCD, SLA, and DLP 3D printers. This manual provides comprehensive instructions for setting up, operating, and maintaining your Wash and Cure 3 station to ensure optimal performance and longevity.
Key features include a larger cleaning basket capacity (42% increase compared to Wash & Cure 2), a flexible gooseneck light for precise curing of intricate details, a dual-layer design for efficient IPA usage, and improved curing uniformity. The machine is engineered for quiet and simple operation, making your 3D printing workflow smoother and more enjoyable.
What's in the Box
Upon unboxing, please verify that all components listed below are present:
- Wash and cure machine
- Washing bucket x1
- Washing basket x1
- Rack bar x4
- Curing table x1
- Gooseneck light x1
- Hex key set x1
- User manual x1
- Power adaptor x1
Figure 1: All components included in the ANYCUBIC Wash and Cure 3 package.
Setup
- Unpack all components from the box and place the Wash and Cure 3 machine on a stable, level surface.
- Ensure the area is well-ventilated and away from direct sunlight.
- Connect the power adapter to the machine and a suitable power outlet.
- Familiarize yourself with the control panel and its functions (Wash, Cure, FlexiCure modes, timer knob).
Figure 2: The ANYCUBIC Wash and Cure 3 unit ready for setup.
Operating Instructions
1. Wash Mode
The Wash Mode is used to clean uncured resin from your 3D printed models. The Wash and Cure 3 features a significantly increased cleaning basket capacity and a dual-layer design for efficient cleaning.
- Place the washing bucket onto the machine's platform.
- Fill the washing bucket with an appropriate cleaning solution (e.g., Isopropyl Alcohol - IPA) up to the recommended level, ensuring the model will be fully submerged. The bucket has a 4L capacity.
- Place your resin print into the washing basket. The dual-layer design allows for two adjustable heights (100mm and 165mm) to accommodate various print platforms from 5.9 to 7.3 inches.
- Lower the washing basket with the print into the cleaning solution.
- Close the yellow transparent cover securely.
- Select "Wash" mode on the control panel.
- Adjust the washing time using the rotary knob (1 to 30 minutes). Recommended times are typically 2, 4, or 6 minutes depending on model size and resin type.
- Press the Start button to begin the washing cycle. The machine will agitate the solution to effectively clean the model.
- Once the cycle is complete, remove the print from the washing basket and allow it to dry thoroughly before proceeding to curing.
Figure 3: The 4L washing bucket with increased capacity for larger models.
Figure 4: The dual-layer cleaning basket offers adjustable heights for different print sizes, optimizing IPA usage.
Wash Mode Demonstration Video:
Video 1: Official demonstration of the Wash Mode in action, showing the agitation process.
2. Cure Mode
After washing and drying, models need to be cured to achieve their final hardness and strength. The Wash and Cure 3 features enhanced curing power and a unique gooseneck light for precise curing.
- Remove the washing bucket and place the curing table onto the machine's platform.
- Carefully place your dry resin print onto the curing table.
- Close the yellow transparent cover securely.
- Select "Cure" mode on the control panel.
- Adjust the curing time using the rotary knob (1 to 30 minutes).
- Press the Start button to begin the curing cycle. The internal UV lights will activate, and the curing table will rotate to ensure even exposure.
- For models with intricate details or hard-to-reach areas, activate the "FlexiCure" gooseneck light by pressing its dedicated button. This light provides concentrated UV exposure to strengthen subtle areas.
- Once the curing cycle is complete, the machine will stop. Your model is now fully cured and ready for further post-processing or use.
Figure 5: The intuitive control panel for selecting wash, cure, or FlexiCure modes and adjusting time.
Figure 6: The innovative FlexiCure Gooseneck Light design provides targeted UV exposure for enhanced curing of subtle areas.
Cure Mode Demonstration Video:
Video 2: Official demonstration of the Cure Mode, showing the rotating platform and UV light array.
Safety Features
The ANYCUBIC Wash and Cure 3 is designed with user safety in mind. The yellow transparent cover blocks 99.995% of UV light, protecting your eyes during operation. Additionally, a safety switch automatically pauses the curing process if the lid is removed during operation, preventing accidental UV exposure.
Maintenance
Regular maintenance ensures the longevity and optimal performance of your Wash and Cure 3 station:
- Cleaning the Washing Bucket: After multiple uses, the cleaning solution may become saturated with resin. Replace the solution as needed. Clean the washing bucket and basket with fresh IPA or warm soapy water. Ensure they are completely dry before refilling.
- Cleaning the Machine: Wipe down the exterior of the machine, including the transparent cover and control panel, with a soft, damp cloth. Avoid using abrasive cleaners that could scratch surfaces.
- UV Light Maintenance: Keep the UV LED strips and the curing table clean from any resin residue to ensure efficient curing. Use a soft cloth and IPA if necessary.
- Resin Disposal: Always dispose of used resin and contaminated IPA according to local regulations. Do not pour them down the drain.
Troubleshooting
If you encounter any issues with your ANYCUBIC Wash and Cure 3, refer to the following common troubleshooting tips:
- Machine Not Turning On:
- Check if the power adapter is securely connected to both the machine and the power outlet.
- Ensure the power outlet is functional.
- Wash/Cure Cycle Not Starting:
- Verify that the transparent cover is properly closed and seated. The safety switch prevents operation if the lid is open.
- Ensure the correct mode (Wash or Cure) is selected.
- Incomplete Curing:
- Increase the curing time.
- Ensure the model is clean and dry before curing.
- Utilize the FlexiCure gooseneck light for complex geometries.
- Check if the UV LEDs are functioning correctly.
- Ineffective Washing:
- Replace the cleaning solution if it's heavily contaminated.
- Ensure the model is fully submerged in the cleaning solution.
- Increase the washing time.
For more detailed troubleshooting or persistent issues, please refer to the official user manual PDF or contact ANYCUBIC customer support.
Specifications
| Feature | Detail |
|---|---|
| Product Dimensions | 8.86 x 8.66 x 14.88 inches |
| Item Weight | 0.01 ounces |
| Model Number | Wash and Cure 3 |
| Brand | ANYCUBIC |
| Material | PC+metal |
| Color | multi-color |
| Manufacturer | ANYCUBIC |
| Date First Available | January 4, 2020 |
| Maximum Cleaning Volume (without platform) | 165 x 100 x 180 mm |
| Maximum Cleaning Volume (with platform) | 165 x 100 x 160 mm |
| Maximum Curing Size | Φ160 x 180 mm |
| UV Light | 10pcs 405nm + Gooseneck Light |
Table 1: Technical specifications of the ANYCUBIC Wash and Cure 3.
Warranty and Support
ANYCUBIC products typically come with a standard manufacturer's warranty. Please refer to the warranty card included in your product packaging for specific terms and conditions. For technical support, troubleshooting assistance, or warranty claims, please visit the official ANYCUBIC website or contact their customer service directly.
An official User Guide (PDF) is available for download: Download User Guide
