VGEBY S810

Download PDF
Contents

VGEBY S810 LED Electric Display Control Panel User Manual

Model: S810

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the VGEBY S810 LED Electric Display Control Panel. Designed for electric bicycles and scooters, this display is compatible with 36V and 48V systems and integrates with JN Controllers and Pasion Electric Motor Kits. Please read this manual thoroughly before use to ensure proper function and safety.

2. Safety Information

  • Always ensure the power is off before installing or removing the display.
  • Do not attempt to disassemble or modify the display unit. This may void the warranty and cause damage.
  • Keep the display away from water and extreme temperatures.
  • Ensure all connections are secure to prevent electrical shorts or malfunctions.
  • Regularly check the display and wiring for any signs of damage.

3. Product Overview

The S810 LED Electric Display provides essential information and control for your electric vehicle. It features an intuitive interface with buttons for power, light control, and mode selection, along with indicators for battery level and thrust settings.

VGEBY S810 LED Electric Display Control Panel

Figure 3.1: Front view of the VGEBY S810 LED Electric Display Control Panel, showing the 'ON/OFF', 'LIGHT', and 'MODE' buttons, along with power and thrust indicators. The green connector is visible on the cable.

VGEBY S810 LED Electric Display with dimensions

Figure 3.2: The S810 display with approximate dimensions: 82mm (3.2in) width and 42mm (1.7in) height. The wire length with connector is approximately 21.5cm (8.5in).

Close-up of JULET connector

Figure 3.3: Close-up view of the JULET connector, which ensures a secure and compatible connection to the electric system.

4. Setup and Installation

4.1 Compatibility

  • Voltage: Compatible with 36V and 48V electric systems.
  • Handlebar Diameter: Suitable for 22.2mm (0.87in) diameter handlebars.
  • Controller/Motor Kit: Designed for use with JN Controllers and Pasion Electric Motor Kits.
  • Communication Protocol: The S810 display requires products that are consistent with its communication protocol for proper function.

4.2 Installation Steps

  1. Prepare Handlebar: Ensure the handlebar area where the display will be mounted is clean and free of obstructions. The display is designed for 22.2mm diameter handlebars.
  2. Mount Display: Position the S810 display on the handlebar in a comfortable and visible location. Secure it using the integrated mounting bracket and screws.
  3. Rear view of S810 display with mounting bracket

    Figure 4.1: Rear view of the S810 display, showing the mounting bracket and screw for handlebar attachment.

  4. Connect Wiring: Connect the display's cable to the corresponding port on your electric bicycle's controller (e.g., JN Controller). Ensure the JULET connector is fully inserted and secure.
  5. S810 display mounted on a bicycle handlebar

    Figure 4.2: The S810 display correctly mounted on a 22.2mm diameter bicycle handlebar, demonstrating its typical installed position.

  6. Verify Connection: After installation, double-check all connections to ensure they are tight and correctly aligned.

5. Operating Instructions

The S810 display offers straightforward controls for managing your electric vehicle's functions.

Angled view of S810 display showing buttons and indicators

Figure 5.1: Angled view of the S810 display, highlighting the 'ON/OFF', 'LIGHT', and 'MODE' buttons, along with the power and thrust level indicators.

5.1 Power On/Off

  • Press the ON/OFF button to power on the display and the electric system.
  • Press and hold the ON/OFF button to power off the system.

5.2 Light Control

  • Press the LIGHT button to turn the vehicle's lights on or off.

5.3 Mode/Thrust Control

  • Press the MODE button to cycle through different thrust levels: LOW, MED (Medium), and HIGH.
  • The corresponding indicator lights (Low, Med, High) will illuminate to show the currently selected thrust level.
  • The display features a gear memory function, which automatically restores the last selected gear setting upon power-on.

5.4 Power Display

  • The power indicator section (labeled 'POWER') accurately shows the true battery power level.
  • The display also records real-time power consumption, allowing you to track your riding mileage effectively.
Close-up of S810 power and thrust indicators

Figure 5.2: Detailed view of the 'POWER' indicator and the 'LOW-MED-HIGH' thrust level indicators on the S810 display.

6. Maintenance

  • Cleaning: Wipe the display surface with a soft, damp cloth. Do not use abrasive cleaners or solvents.
  • Inspection: Periodically check the wiring and connectors for any signs of wear, corrosion, or damage. Ensure the display is securely mounted.
  • Storage: If the electric vehicle is stored for an extended period, ensure the display is powered off and stored in a dry, temperate environment.

7. Troubleshooting

  • Display Not Powering On:
    • Check if the main battery of the electric vehicle is charged.
    • Ensure all cable connections, especially the main power cable to the display, are secure.
    • Verify that the display is compatible with your controller's communication protocol.
  • Incorrect Power Reading:
    • Ensure the display is correctly configured for your 36V or 48V system (if adjustable, though S810 is typically auto-sensing).
    • Check the battery connections for any loose contacts.
  • Buttons Unresponsive:
    • Power cycle the display by turning it off and on again.
    • Ensure no debris is obstructing the buttons.
  • Lights Not Activating:
    • Check the connection between the display and the vehicle's lighting system.
    • Verify the lights themselves are functional.

If problems persist, consult a qualified technician or contact customer support.

8. Specifications

FeatureSpecification
Item TypeLED S810 Electric Display
MaterialPlastic
Display SizeApprox. 82x42mm / 3.2x1.7in
Wire Length (with Connector)Approx. 21.5cm / 8.5in
Applicable Handlebar Diameter22.2mm / 0.87in
Voltage Compatibility36V, 48V
Interface TypeInterface (JULET type connector)
ApplicationFor JN Controller and Pasion Electric Motor Kit
Package Dimensions5.12 x 3.54 x 3.15 inches
Item Weight3.39 ounces (Approx. 96g)
Batteries RequiredNo
S810 display with examples of electric bicycles and scooters

Figure 8.1: The S810 display shown alongside an electric bicycle and an electric scooter, illustrating its intended applications.

9. Warranty and Support

VGEBY products are manufactured to high-quality standards. For warranty information or technical support, please refer to the documentation provided with your purchase or contact your retailer. Keep your proof of purchase for warranty claims.

© 2025 VGEBY. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.