Behringer WING Rack 48-channel Digital Mixer User Manual

Introduction

This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your Behringer WING Rack 48-channel Digital Mixer. Please read this manual thoroughly before operating the device to ensure proper use and to maximize its performance and longevity.

Figure 1: Front view of the Behringer WING Rack 48-channel Digital Mixer, showcasing the touchscreen display, faders, and control knobs.

Important Safety Instructions

Always follow basic safety precautions when using this product to reduce the risk of fire, electric shock, and injury to persons.

• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with dry cloth.
• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
• Only use attachments/accessories specified by the manufacturer.
• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
• Unplug this apparatus during lightning storms or when unused for long periods of time.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Setup

Unpacking and Inspection

Carefully unpack the WING Rack and inspect it for any signs of damage that may have occurred during transit. If any damage is found, contact your dealer immediately. Retain the original packing materials for future use or if the unit needs to be returned for service.

Rack Mounting

The WING Rack is designed for standard 19-inch rack mounting. Ensure adequate ventilation around the unit. Do not block the ventilation openings. Use appropriate rack screws to secure the unit firmly in place.

Power Connection

Connect the supplied AC power cord to the WING Rack's power inlet and then to a suitable power outlet. Ensure the power source matches the voltage requirements specified on the unit. Always use a grounded outlet.

Initial Connections

The WING Rack offers extensive connectivity. Below are common initial connections:

• Audio Inputs: Connect microphones, line-level instruments, or other audio sources to the Midas Pro preamps on the rear panel.
• Audio Outputs: Connect main outputs to your power amplifier or powered speakers. Connect auxiliary outputs to monitor systems or effects processors.
• USB Audio Interface: Connect a USB cable from the WING Rack to your computer for 48-in/48-out audio recording and playback.
• Network Connection: For remote control via mobile devices or desktop applications, connect an Ethernet cable to a network router.
• Expansion Slots: Utilize the expansion slots for optional cards such as Dante, MADI, or ADAT for additional digital I/O.

Operating Instructions

Powering On and Off

To power on, ensure all connections are secure, then press the power button located on the rear panel. To power off, press and hold the power button until the unit shuts down. It is recommended to power down connected amplifiers and speakers before powering off the WING Rack.

Touchscreen Navigation

The 10.1-inch capacitive touchscreen is the primary interface for controlling the WING Rack. Navigate through menus and adjust parameters by tapping, swiping, and using the rotary encoders adjacent to the screen.

Figure 2: Close-up of the WING Rack's touchscreen display, showing channel faders and metering.

Source Paradigm

The WING Rack utilizes a "Source" paradigm, allowing you to focus on the audio source rather than specific channels. Sources can be assigned to multiple channels, providing flexible routing and processing. Access the Source menu from the main screen to configure and manage your audio inputs.

Channel Processing

Each channel on the WING Rack offers comprehensive processing capabilities, including:

• Gain Control: Adjust input levels for optimal signal-to-noise ratio.
• Equalization (EQ): Shape the tonal characteristics of your audio.
• Dynamics: Apply compression, gating, and expansion to control dynamic range.
• Effects: Access 16 stereo digital FX processors for reverb, delay, modulation, and more.
• Routing: Assign channels to buses, matrices, and main outputs.

Recording and Playback

The WING Rack supports direct recording to dual SD cards (up to 64 channels) and acts as a 48-in/48-out USB audio interface for recording to a Digital Audio Workstation (DAW) on your computer.

• SD Card Recording: Insert two SD cards into the dedicated slots. Navigate to the recording section on the touchscreen to arm tracks and start recording.
• USB Audio: Ensure the WING Rack is connected to your computer via USB. Select the WING Rack as your audio interface in your DAW settings.

Maintenance

Cleaning

Regularly clean the exterior of the WING Rack with a soft, dry cloth. For the touchscreen, use a microfiber cloth specifically designed for electronic displays. Do not use abrasive cleaners, solvents, or waxes, as these can damage the finish or screen.

Firmware Updates

Behringer periodically releases firmware updates to improve performance, add features, and fix bugs. Check the official Behringer website for the latest firmware. Follow the instructions provided with the firmware update package carefully to avoid damaging the unit.

Ventilation

Ensure that the ventilation openings are clear of dust and debris. Proper airflow is crucial for preventing overheating and ensuring the longevity of the internal components. Do not operate the unit in enclosed spaces without adequate air circulation.

Troubleshooting

This section provides solutions to common issues you might encounter with your WING Rack.

If the problem persists after attempting these solutions, please contact Behringer customer support or a qualified service technician.

Specifications

Below are the key technical specifications for the Behringer WING Rack 48-channel Digital Mixer:

• Model: WING Rack
• Channels: 48 stereo channels
• Preamps: 24 Midas Pro Preamps
• USB Audio Interface: 48-in/48-out
• Digital FX Processors: 16 stereo
• Buses: 28 Stereo Buses
• Display: 10.1-inch capacitive touchscreen
• Recording: Direct to dual SD cards (up to 64 channels)
• Dimensions: 25.3 x 19.6 x 15.6 inches (Width x Depth x Height, approximate)
• Weight: 31.8 pounds (14.4 kg)
• Power Supply: AC 100-240V, 50/60Hz (typical for audio equipment)
• ASIN: B0D7QLX7MG
• UPC: 644216654307

Warranty Information

Behringer products are covered by a limited warranty. For detailed information regarding the warranty period, terms, and conditions applicable to your WING Rack, please refer to the warranty card included with your product or visit the official Behringer website. Keep your proof of purchase for warranty claims.

Support and Service

For technical support, service, or spare parts, please contact Behringer customer support. You can find contact information and frequently asked questions (FAQs) on the official Behringer website:

www.behringer.com/support

When contacting support, please have your product model (WING Rack) and serial number ready. The serial number is typically located on the rear or bottom panel of the unit.