1. Introduction
This manual provides essential information for the proper use and maintenance of your ResMed AirFit F40 Full Face Replacement Cushion, Medium size. This cushion is designed to provide a soft, comfortable, and secure fit for effective CPAP therapy.
The silicone material of the cushion is engineered to move and adapt to your face, helping to maintain a consistent seal throughout the night.

Image 1.1: The ResMed AirFit F40 Full Face Replacement Cushion in Medium size.
2. Safety Information
2.1 General Safety
Keep the mask magnets at a safe distance of at least 6 inches (150 mm) away from implants or medical devices that may be adversely affected by magnetic interference. This warning applies to you or anyone in close physical contact with your mask. The magnets are located in the frame and lower headgear clips, with a magnetic field strength of up to 400mT. When worn, they connect to secure the mask but may inadvertently detach while asleep.
2.2 Contraindications
Masks with magnetic components are contraindicated for use by patients where they, or anyone in close physical contact while using the mask, have the following:
- Active medical implants that interact with magnets (i.e., pacemakers, implantable cardioverter defibrillators (ICD), neurostimulators, cerebrospinal fluid (CSF) shunts, insulin/infusion pumps).
- Metallic implants/objects containing ferromagnetic material (i.e., aneurysm clips/flow disruption devices, embolic coils, stents, valves, electrodes, implants to restore hearing or balance with implanted magnets, ocular implants, metallic splinters in the eye).
3. Setup and Installation
The AirFit F40 replacement cushion is designed for easy integration with your existing AirFit F40 mask system. Ensure you have the correct cushion size for your mask frame.
3.1 Checking Cushion Size
Before installation, verify that the replacement cushion matches the size indicated on your mask frame. The size is typically marked on the cushion itself.

Image 3.1: Verify the cushion size, indicated by 'M' for Medium.
3.2 Attaching the Cushion
Align the replacement cushion with the mask frame. Gently press the cushion onto the frame until it securely clicks into place. Ensure there are no gaps or misalignments that could lead to air leaks.

Image 3.2: The AirFit F40 cushion integrates with the mask frame and headgear (headgear not included with cushion).
4. Operating the Mask with New Cushion
Once the cushion is securely attached to the mask frame, connect your CPAP tubing and adjust the headgear for a comfortable and effective seal. The soft silicone design is intended to conform to your facial contours.

Image 4.1: The AirFit F40 mask with its cushion provides a soft and secure fit.
5. Maintenance
Regular cleaning and timely replacement of your cushion are crucial for hygiene, comfort, and effective therapy.
5.1 Daily Cleaning Instructions
To maintain optimal performance and hygiene, clean your AirFit F40 cushion daily:
- Soak the cushion in warm water with a mild liquid detergent.
- Shake vigorously in the water and hand wash with a soft bristle brush.
- Thoroughly rinse under running water.
- Leave to air dry out of direct sunlight.

Image 5.1: Steps for daily cleaning of your AirFit F40 cushion.
5.2 Replacement Schedule
It is recommended to replace your cushion monthly to ensure optimal seal and hygiene. Signs that indicate it might be time to replace your cushion include:
- Cracks
- Tears
- Other visible signs of deterioration

Image 5.2: Recommended monthly replacement for the AirFit F40 cushion.
6. Troubleshooting
If you experience issues with your AirFit F40 replacement cushion, consider the following:
- Air Leaks: Ensure the cushion is correctly seated on the mask frame and that the headgear is adjusted for a snug, but not overly tight, fit. Check for any visible damage or tears on the cushion.
- Discomfort: Re-adjust the headgear to relieve pressure points. Ensure the cushion size is appropriate for your face. If discomfort persists, consult your healthcare provider.
- Cushion Deterioration: If the cushion shows signs of wear, cracks, or tears, it should be replaced immediately to maintain an effective seal and hygiene.
7. Specifications
| Attribute | Detail |
|---|---|
| Product Dimensions | 3.65 x 1.78 x 2.85 inches |
| Item Weight | 1.12 ounces |
| Manufacturer | ResMed |
| ASIN | B0D7NCGZVZ |
| Material | Silicone |
8. Warranty and Support
For specific warranty information regarding your ResMed AirFit F40 Full Face Replacement Cushion, please refer to the documentation provided with your complete ResMed AirFit F40 mask system or visit the official ResMed website. For further assistance or support, contact your medical equipment provider or ResMed customer service.