Introduction
Thank you for choosing the Evolution Power Tools 119-0050 Folding Table Saw Stand. This stand is designed to provide a stable, portable, and efficient workstation for your Evolution R255TBL and R255TBL+ table saws. Please read this manual carefully before assembly and operation to ensure safe and correct use of the product.
Safety Information
Always observe basic safety precautions when using this product to reduce the risk of injury. Keep this manual for future reference.
- Ensure all components are securely fastened before use.
- Do not exceed the maximum weight capacity of the stand.
- Operate on a stable, level surface.
- Keep children and bystanders away from the work area.
- Always wear appropriate personal protective equipment (PPE) when operating power tools mounted on the stand.
Package Contents
Verify that all parts are present before beginning assembly. If any parts are missing or damaged, contact Evolution Power Tools customer support.
- Folding Table Saw Stand Frame
- All-terrain Wheels (2)
- Adjustable Feet (2)
- Assembly Hardware (bolts, washers, nuts)
- Instruction Manual
Setup and Assembly
Follow these steps for quick and easy assembly of your table saw stand.
- Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, flat surface.
- Assemble the Frame: Connect the main frame sections according to the diagrams provided. Ensure all pivot points are correctly aligned.
- Attach Wheels: Securely attach the two all-terrain wheels to the designated axle points on the stand frame using the provided hardware.
- Install Adjustable Feet: Screw the two adjustable feet into the remaining leg supports. These feet allow for leveling on uneven surfaces.
- Mount Table Saw: Position your Evolution R255TBL or R255TBL+ table saw onto the stand's mounting brackets. Use the supplied saw mounting hardware (O x4) to firmly bolt the saw to the stand. This process typically takes less than one minute.
Figure 1: Quick and easy assembly showing saw mounting hardware.
Figure 2: The Evolution table saw stand with a compatible table saw mounted.
Operating Instructions
This stand enhances the functionality and portability of your Evolution table saw.
Using the Stand
- Stability: Once the saw is mounted, ensure the stand is placed on a firm, level surface. Use the adjustable feet to compensate for any unevenness, ensuring maximum stability during operation.
- Portability: The stand features large all-terrain wheels for easy movement. To move the stand, tilt it onto its wheels and roll it to your desired location. The design allows it to fit through standard 81.3 cm (32 inch) doorways.
- Folding for Storage: The stand is designed to fold compactly, even with the saw attached. To fold, release the locking mechanisms (refer to specific saw manual for detachment if necessary, though the stand is designed to fold with it). Once folded, the stand rests on its own feet for convenient storage.
Figure 3: Effortless portability of the folded stand.
Figure 4: Mobility across any jobsite with large diameter all-terrain wheels.
Maintenance
Regular maintenance ensures the longevity and safe operation of your stand.
- Cleaning: Wipe down the stand with a damp cloth to remove dust and debris. The all-terrain wheels are easy to clean.
- Inspection: Periodically check all bolts, nuts, and fasteners to ensure they are tight. Retighten as necessary.
- Lubrication: Apply a light lubricant to moving parts and pivot points as needed to ensure smooth folding and unfolding.
- Storage: Store the stand in a dry, protected area when not in use.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Stand is unstable. | Uneven surface; loose fasteners; adjustable feet not properly set. | Move to a level surface. Check and tighten all fasteners. Adjust the feet to stabilize the stand. |
| Difficulty folding/unfolding. | Debris in pivot points; lack of lubrication; bent component. | Clean pivot points. Apply lubricant. Inspect for damage; contact support if bent. |
| Saw does not fit securely. | Incorrect saw model; mounting hardware not tightened. | Ensure saw is Evolution R255TBL or R255TBL+. Tighten all mounting bolts securely. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | 119-0050 |
| Compatibility | Evolution R255TBL, R255TBL+ Table Saws |
| Material | Alloy Steel |
| Product Dimensions (LxWxH) | 73 x 60 x 88 cm (28.7 x 23.6 x 34.6 inches) |
| Item Weight | 8 kg (17.6 lbs) |
| Special Features | Compact, Quick Assembly, Foldable, All-terrain Wheels, Adjustable Feet |
| Assembly Required | Yes |
Warranty
This Evolution Power Tools 119-0050 Folding Table Saw Stand comes with a 2-year limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. For full terms and conditions, please refer to the warranty card included with your product or visit the official Evolution Power Tools website.
Customer Support
If you have any questions, require assistance with assembly, or need to troubleshoot an issue, please contact Evolution Power Tools customer support.
- Website: www.evolutionpowertools.com
- Email: Refer to website for contact form or email address.
- Phone: Refer to website for regional contact numbers.
Please have your model number (119-0050) and purchase date available when contacting support.
