Klever Kits Unicorn Soap Making Kit

1. Introduction

Welcome to the magical world of soap making with the Klever Kits Unicorn Soap Making Kit! This kit allows you to create your own unique, scented, and colorful unicorn-themed soaps. It's a fun and engaging activity that combines creativity with basic science principles, perfect for young crafters.

Please read these instructions carefully before beginning to ensure a safe and enjoyable experience.

2. Safety Information

• Adult Supervision Recommended: While the materials are non-toxic, adult supervision is advised, especially during the soap melting process.
• Age Recommendation: This kit is suitable for ages 6 and up.
• Avoid Ingestion: Do not eat or ingest any components of this kit.
• Eye Contact: In case of eye contact with soap base or colorants, rinse thoroughly with water. If irritation persists, seek medical attention.
• Ventilation: Work in a well-ventilated area.

3. What's Included

Your Klever Kits Unicorn Soap Making Kit contains all the necessary items to create beautiful soaps:

• 4 Soap Molds (Unicorn, Rainbow, Unicorn Narwhal, Hearts)
• 10 Soap Base Blocks
• 2 Fragrances (Lemon and Apple)
• 4 Colorants (Red, Blue, Yellow, Pink)
• Glitter
• 1 Beaker
• 6 Pop Sticks (Stirring Tools)
• 1 Working Tray
• 1 Trimming Tool
• Instruction Guide

4. Setup

1. Prepare Your Workspace: Choose a clean, flat, and heat-resistant surface. Cover it with newspaper or a protective mat to prevent spills.
2. Organize Materials: Lay out all the kit components within easy reach.
3. Place Molds: Position your chosen soap molds in the working tray. The tray helps stabilize the molds during pouring and setting.

5. Operating Instructions

Step 1: Melt the Soap Base

1. Remove the transparent film from the soap blocks.
2. Place 1-2 soap base blocks into the provided beaker. The number of blocks depends on the size of your chosen mold.
3. Heat the beaker in the microwave for 10 seconds. Check the soap; if large pieces remain, stir and continue heating in 4-second increments until completely melted.

Step 2: Add Color, Scent, and Glitter

1. Once the soap base is melted, add 1-3 drops of your desired colorant(s) and fragrance(s) to the melted soap. Refer to the color guide below for mixing suggestions.
2. Add a pinch of glitter for extra sparkle.
3. Use a pop stick to thoroughly stir the mixture until all ingredients are evenly distributed.

Step 3: Pour into Molds

1. Carefully pour the colored and scented soap mixture into your chosen molds. Fill to the top edge of the mold.
2. If creating layered soaps, pour one color, allow it to set slightly (a few minutes), then pour the next color.

Step 4: Allow to Set

1. Let the filled molds cool and harden at room temperature for approximately 45 minutes.
2. For faster setting, place the molds in a refrigerator or freezer for about 20 minutes.

Step 5: Demold and Trim

1. Once completely hardened, gently flex the molds to release your custom-made soaps.
2. Use the trimming tool to carefully remove any excess soap around the edges for a smooth finish.

Color Mixing Guide

Experiment with different color combinations to create unique shades:

• Yellow + Blue = Green
• Red + Yellow = Orange
• Red + Blue = Purple

6. Media Resources

Official Product Video

7. Maintenance

• Cleaning Molds and Tools: After each use, wash the molds, beaker, and trimming tool with warm, soapy water. Rinse thoroughly and allow to air dry.
• Storing Materials: Store unused soap base blocks, colorants, fragrances, and glitter in their original containers in a cool, dry place away from direct sunlight.
• Soap Storage: Store finished soaps in an airtight container to preserve their scent and prevent them from drying out.

8. Troubleshooting

• Soap Not Melting Properly: If the soap base is not fully melted after microwaving, continue heating in short 4-second bursts, stirring between each interval. Ensure the soap is completely liquid before adding colors and scents.
• Excessive Bubbles: Stir the melted soap gently to minimize air bubbles. If bubbles appear on the surface after pouring into molds, lightly spray with rubbing alcohol (not included) to dissipate them.
• Soap Not Setting: Ensure the molds are placed in a cool environment. If using the freezer, do not leave them in for too long as this can cause condensation.
• Difficulty Demolding: If soaps are difficult to remove, ensure they are fully hardened. Gently push from the bottom of the flexible silicone molds.

9. Specifications

10. Warranty and Support

Klever Kits is committed to providing high-quality products. If you encounter any issues or have questions regarding your Unicorn Soap Making Kit, please contact our customer support for assistance. We strive to ensure your satisfaction with our products.

For further support or inquiries, please visit the official Klever Kits store on Amazon or contact their customer service directly.