Introduction
This manual provides instructions for the Anderic RR7222T Ceiling Fan Remote Control. This remote is designed as a direct replacement for specific ceiling fan models from brands such as Hampton Bay, Home Decorators Collection, and Harbor Breeze. It offers control over fan speeds and lighting functions.
Important: This remote is not a universal remote and is only compatible with specific receivers. Please verify compatibility before use.
Compatibility
The Anderic RR7222T remote is compatible with ceiling fan systems that use the following FCC IDs and receiver models:
- FCC IDs: UC7222T, CHQ7222T
- Receiver Models: MR7703, UC7301R, UC7301R-01, UC7301R-03, UC7305R
Not Compatible With: MR77A, smart fans, or other universal remote systems. This remote does not include a receiver.
Image Description: This image illustrates the importance of confirming your fan's FCC ID. It shows the back of two different remote controls, one with FCC ID CHQ7222T and another with CHQ7222T434, emphasizing that the correct matching FCC ID is crucial for proper pairing. You must check the back of your old remote to ensure compatibility.
For more information on compatibility, visit: https://qr.link/miQyRB
Image Description: This image highlights the wide receiver compatibility of the Anderic RR7222T remote. It lists compatible brands and receiver models, including Home Decorators Collection, Hampton Bay, Harbor Breeze, MR7703, UC7301R, UC7301R-01, UC7301R-03, and UC7305R, ensuring seamless integration.
Battery Installation
The Anderic RR7222T remote requires one A23 12-volt battery (not included).
- Locate the battery compartment on the back of the remote control.
- Slide the battery cover open.
- Insert one A23 12-volt battery, ensuring the polarity (+/-) matches the diagram inside the compartment.
- Close the battery cover securely.
Image Description: This image shows the remote's internal dip switches and a 12-volt A23 battery, which is required but not included. It visually supports the battery installation and pairing steps.
Setup & Pairing (Dip Switch Configuration)
To pair your Anderic RR7222T remote with your ceiling fan receiver, follow these steps:
- Set Dip Switches: Open the battery compartment on your new remote. Locate the four-pin code switches. Match the position of these switches (up or down) to the corresponding switches on your ceiling fan's receiver unit. If you are replacing an old remote, match the dip switch settings from your old remote.
- Turn Off Power: Turn off the main power to your ceiling fan at the circuit breaker or wall switch.
- Restore Power: Restore power to the fan.
- Pair Remote: Within 30 seconds of restoring power, press and hold the POWER key (the large button with the power symbol) on the remote for up to 10 seconds. The fan light should blink or the fan should respond, indicating successful pairing.
If pairing is unsuccessful, repeat the steps, ensuring the dip switches are correctly matched and the power cycle is performed within the specified timeframe.
Image Description: This image visually guides the user through the 4-step pairing process, showing how to set the dip switches and the required 12-volt A23 battery. It emphasizes the importance of matching the dip switch settings for successful pairing.
Operating Instructions
The Anderic RR7222T remote provides comprehensive control over your ceiling fan and its integrated lighting.
Image Description: This image displays both the front and back of the Anderic RR7222T remote control. The front illustrates the button layout for fan speed, power, fan direction, and light control, while the back shows important regulatory information and a QR code for support.
For additional support, scan the QR code: https://qr.link/miQyRB
Fan Control:
- Power On/Off: Press the large POWER button to turn the fan on or off.
- Fan Speeds: Use buttons labeled 1, 2, and 3 to select low, medium, and high fan speeds, respectively.
- Fan Direction: Press the FAN DIRECTION button (circular arrow) to reverse the fan's rotation, typically used for seasonal comfort (downward airflow for cooling, upward for heat distribution).
Light Control:
- Light On/Off: Press the LIGHT button (bulb icon) to turn the fan light on or off.
- Dimming: If your fan uses incandescent bulbs, press and hold the LIGHT button to dim or brighten the light. Release the button when the desired brightness is reached.
Image Description: This image demonstrates the complete control offered by the remote, including fan speeds and light dimming. It shows a user adjusting airflow and brightness from a seated position, highlighting the convenience of the remote's functions.
Wall Mount Installation
A wall mount bracket and screws are included for convenient storage and easy access to your remote control.
- Choose a suitable location on a wall, away from direct sunlight or heat sources.
- Use the provided screws to secure the wall mount bracket to the wall. Ensure it is level and firmly attached.
- Slide the remote control into the mounted bracket.
Image Description: This image illustrates the included wall mount bracket, showing the remote neatly stored on a wall. It highlights how the mount provides quick access and helps keep the remote organized, preventing it from being misplaced.
Troubleshooting
- Remote Not Responding:
- Check the battery: Ensure the A23 12-volt battery is correctly installed with proper polarity and is not depleted. Replace if necessary.
- Re-pair the remote: Follow the "Setup & Pairing" instructions to re-sync the remote with the receiver.
- Verify compatibility: Double-check that your fan's receiver FCC ID and model number match the compatible list for the RR7222T.
- Light Dimming Not Working:
- Dimming functionality is primarily designed for incandescent bulbs. CFL or LED bulbs may not dim properly or at all with this remote.
- Ensure you are pressing and holding the light button for dimming, not just pressing it briefly.
- Fan Not Changing Speeds:
- Confirm the remote is paired correctly.
- Ensure there are no obstructions between the remote and the fan's receiver.
Specifications
| Feature | Detail |
|---|---|
| Model Number | RR7222T (Replaces UC7222T CHQ7222T) |
| Brand | Anderic |
| Compatible FCC IDs | UC7222T, CHQ7222T |
| Compatible Receivers | MR7703, UC7301R, UC7301R-01, UC7301R-03, UC7305R |
| Functions | 3 Fan Speeds, Fan On/Off, Light On/Off, Light Dimming (incandescent only), Fan Direction |
| Battery Required | 1 x A23 12-volt battery (not included) |
| Color | Black |
| Special Feature | Ergonomic design, Wall mount included |
| Dimensions | Approx. 6.85 x 2.83 x 1.38 inches |
| Item Weight | Approx. 2.08 ounces |
Image Description: This image provides a visual representation of the remote's compact dimensions, showing it is designed to fit naturally in hand and integrate well into any space.
Support
If you encounter any issues or have questions regarding the compatibility or operation of your Anderic RR7222T remote control, please contact our support team.
When contacting support, please provide your ceiling fan's model number and the FCC ID of its receiver for faster assistance.
For general inquiries or to visit the Anderic store, please refer to the following link: Anderic Store on Amazon
