Quip Water Flosser Instruction Manual

Introduction

The Quip Water Flosser is designed to enhance your oral hygiene routine by providing effective cleaning between teeth and along the gumline. This cordless device features adjustable pressure settings and a 360-degree rotating tip to reach all areas of your mouth. It is scientifically proven to remove up to 99% of plaque from treated areas.

This manual provides essential information on how to set up, operate, maintain, and troubleshoot your Quip Water Flosser to ensure optimal performance and longevity.

Image: The Quip Water Flosser in black, shown with an additional replacement floss tip and its magnetic charging cable, illustrating the complete package contents.

Setup

1. Attach the Floss Tip: Securely insert the base of the floss tip into the top of the water flosser. It will magnetically snap into place.
2. Fill the Reservoir: Open the lid of the water reservoir and fill it with lukewarm water. Close the lid securely.
3. Initial Charge: Ensure the device is fully charged before first use. Refer to the 'Charging' section for detailed instructions.

Image: A hand holding the Quip Water Flosser under a faucet, demonstrating the easy-fill water reservoir design.

Operating Instructions

1. Positioning: Lean over a sink and close your lips slightly around the floss tip to prevent splashing.
2. Power On: Press the power button to turn on the device.
3. Select Pressure Mode: Press the bottom LED button to switch between gentle (white light) and deep pressure (blue light) modes.
4. Water Flow: Lightly press the 'q' button for on-demand water flow, or press and click for a continuous stream. Press again to turn off the continuous flow.
5. Flossing Technique: Direct the water stream at a 90-degree angle to your gumline. Move the tip along your gumline, pausing briefly on each tooth. Floss each tooth along the gums, front, back, and in between. Start in one quadrant of your mouth and systematically clean all areas.
6. Completion: After use, remove the tip and rinse it under warm water. Empty the reservoir and allow it to air dry.

Image: A close-up of a hand holding the Quip Water Flosser, emphasizing the 360-degree rotating tip designed for hard-to-reach areas.

Charging and Maintenance

Charging

The Quip Water Flosser features a magnetic charging cable for convenience. A full charge takes approximately 4 hours and can last up to 8 weeks when used daily on the gentle mode.

1. Connect Charger: Plug the USB charging cable into a power adapter.
2. Attach to Flosser: Attach the magnet-end of the cable to the flosser base.
3. Indicator Light: The flosser LED button will flash orange when charging and turn solid green when fully charged.

Important: Do not charge if the cable and water flosser contact points are wet. Dry completely to avoid potential damage.

Image: A hand connecting the magnetic charging cable to the base of the Quip Water Flosser, illustrating the ease of charging.

Maintenance

• Tip Replacement: Replace the floss tip every 3 months for optimal performance. An extra tip is included with your purchase.
• Cleaning: After each use, rinse the floss tip and empty the water reservoir. Allow the reservoir to air dry to prevent mildew.
• Storage: Store the flosser with the tip off and the reservoir empty in a clean, dry place.

Specifications

• Item Model Number: 920-01110
• Power Source: Battery Powered (1 Lithium Ion battery included)
• Special Features: Lightweight, Multiple Pressure Settings, Rechargeable, Rotatable Tip
• Product Benefits: Removes Plaque
• Unit Count: 1.0 Count
• Package Dimensions: 10.59 x 7.52 x 2.76 inches; 1 Pound

Warranty and Support

The Quip Rechargeable Water Flosser comes with a 1-Year Limited Warranty. This warranty covers all manufacturing defects from the date of purchase. It excludes normal wear and tear, product misuse, or lost items.

For further assistance or warranty claims, please refer to the official Quip support channels or visit the Quip Store on Amazon.