Introduction
This manual provides essential instructions for the assembly, safe use, and maintenance of your Nathan James Gracie Scandinavian Dining Chair. Please read all instructions carefully before beginning assembly and retain this manual for future reference.
Image: The Gracie dining chair, featuring a cream boucle cushion and dark brown solid wood frame, positioned in a modern dining area.
Safety Information
- Always read and follow all assembly instructions carefully.
- Keep all small parts and packaging materials away from children and pets.
- Assemble the chair on a soft, clean, and level surface to prevent scratches or damage.
- Ensure all bolts, screws, and fasteners are securely tightened before using the chair. Periodically check and re-tighten as necessary.
- Do not stand on the chair.
- The maximum weight capacity for this chair is 300 pounds. Do not exceed this limit.
- Use the chair only for its intended purpose as a dining chair.
Package Contents
Before assembly, verify that all components are present and undamaged. If any parts are missing or damaged, please contact customer support.
- Seat with Upholstery (1)
- Backrest Frame (1)
- Front Legs (2)
- Rear Legs (2)
- Hardware Pack (bolts, washers, Allen wrench)
Image: A diagram illustrating the key features of the Gracie chair, including the exposed wood back, tapered legs, 19-inch seat height, large comfortable seat, boucle linen weave fabric, and C-shape cushion.
Setup and Assembly
Assembly of the Gracie dining chair is designed to be straightforward and typically takes approximately 20 minutes. Follow these steps:
- Unpack Components: Carefully remove all parts from the packaging. Lay them out on a clean, soft surface to prevent scratches.
- Identify Hardware: Locate the hardware pack and identify all bolts, washers, and the Allen wrench.
- Attach Front Legs: Secure the two front legs to the underside of the seat frame using the provided bolts and washers. Do not fully tighten yet.
- Attach Rear Legs: Secure the two rear legs to the underside of the seat frame. Ensure the rear legs align with the backrest attachment points. Do not fully tighten yet.
- Attach Backrest: Align the backrest frame with the rear legs and the back of the seat. Secure it using the remaining bolts and washers.
- Final Tightening: Once all components are loosely assembled, place the chair upright on a level surface. Apply gentle pressure to the seat to ensure it is level, then systematically tighten all bolts using the Allen wrench until secure. Do not overtighten.
Image: A side view of the fully assembled Gracie dining chair, showcasing its profile and the integration of the seat and backrest with the solid wood frame.
Operating Instructions
The Nathan James Gracie Scandinavian Dining Chair is designed for comfortable seating at dining tables or similar surfaces. To use:
- Place the chair on a flat, stable surface.
- Ensure all four legs are evenly touching the floor to prevent wobbling.
- Sit gently onto the chair, distributing your weight evenly.
- Avoid sudden movements or excessive force that could damage the chair or cause instability.
Maintenance and Care
Proper care will extend the life and appearance of your dining chair.
- Cleaning: For general cleaning, wipe the wood frame with a soft, damp cloth. For the boucle upholstery, spot clean with a mild fabric cleaner as needed. Always test cleaners on an inconspicuous area first. Do not use abrasive cleaners or harsh chemicals.
- Hardware: Periodically check all bolts and screws to ensure they remain tight. Re-tighten as necessary to maintain stability.
- Protection: Avoid placing the chair in direct sunlight or near heat sources, as this can cause fading or damage to the wood and fabric.
- Moving: When moving the chair, always lift it rather than dragging it to prevent damage to the legs and floor.
Image: A close-up view showcasing the texture of the cream boucle fabric and the brushed dark brown finish of the solid wood frame, highlighting the materials used in the chair's construction.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Chair wobbles | Uneven floor surface; loose hardware; uneven leg assembly. | Move chair to a level surface. Check and tighten all bolts. If still uneven, slightly loosen bolts, press down on the seat to level, then re-tighten. |
| Parts feel loose after assembly | Hardware not fully tightened during assembly. | Re-tighten all bolts and screws using the provided Allen wrench. Do not overtighten. |
| Scratches on floor | No floor protectors on chair legs. | Attach felt pads or other floor protectors to the bottom of each chair leg (not included). |
Specifications
| Feature | Detail |
|---|---|
| Brand | Nathan James |
| Model Name | Gracie |
| Item Model Number | 27802 |
| Color | Cream Boucle-brushed Dark Brown |
| Product Dimensions (D x W x H) | 23"D x 17"W x 34"H |
| Seat Depth | 21 inches |
| Maximum Weight Recommendation | 300 Pounds |
| Furniture Finish | Rubberwood (Brushed) |
| Fill Material | Foam |
| Upholstery | Boucle Fabric |
| Style | Mid-Century Modern, Scandinavian |
| Assembly Time | Approximately 20 minutes |
| UPC | 842196013224 |
Image: A technical drawing of the Gracie dining chair with key dimensions labeled, including a total height of 34 inches, seat height of 19 inches, depth of 23.5 inches, and width of 17.4 inches.
Warranty and Support
Nathan James stands by the quality of its products. Your Gracie dining chair is backed by a lifetime manufacturer warranty. Additionally, your purchase includes a 100% money-back guarantee for 100 days from the date of purchase.
If you encounter any quality issues, missing parts, or require assistance with your product, please do not hesitate to contact Nathan James customer support. They are committed to providing immediate replacements or solutions without questions asked.
For support, please visit the official Nathan James website or refer to your purchase documentation for contact information.
