JESLED 24-Inch T8 LED Tube Light Instruction Manual

Introduction

Thank you for choosing the JESLED 24-Inch T8 LED Tube Light. This product is designed to provide efficient and bright illumination, serving as an ideal replacement for traditional fluorescent tubes. Its hybrid design supports both Plug & Play (Type A) with existing ballasts and Ballast Bypass (Type B) direct wiring, offering flexible installation options. This manual provides essential information for safe installation, operation, and maintenance.

Image: Visual comparison highlighting the superior performance of JESLED T8 LED Tubes over traditional fluorescent tubes.

Safety Information

Please read all safety instructions carefully before installation and use. Failure to follow these instructions may result in electric shock, fire, or other hazards.

• Always turn off power at the circuit breaker or fuse box before attempting any installation, maintenance, or removal.
• Ensure the voltage supply is compatible with the LED tube light (100-120V, 60Hz).
• Do not attempt to modify the product in any way.
• This product is intended for indoor use only.
• If you are unsure about electrical wiring, consult a qualified electrician.
• Do not use with dimmers unless explicitly stated as compatible.

Package Contents

Your package should contain the following items:

• 12 x JESLED 24-Inch T8 LED Tube Lights

Image: A pack of twelve JESLED 24-inch T8 LED tube lights, illustrating the quantity included in the package.

Setup and Installation

The JESLED T8 LED Tube Light offers two installation methods: Type A (Plug & Play with Ballast) and Type B (Ballast Bypass). Choose the method that best suits your existing fixture and comfort level with electrical work.

General Installation Steps (Applicable to both types):

1. Turn off power: Ensure the power supply to the fixture is completely disconnected at the circuit breaker before beginning.
2. Remove old fluorescent tubes: Carefully remove the existing fluorescent tubes from the fixture.

Method 1: Type A - Plug & Play (with existing ballast)

This method allows for direct replacement of fluorescent tubes without rewiring, provided your existing ballast is compatible.

1. Check Ballast Compatibility: Refer to the ballast compatibility list provided in this manual (or product image 5) to ensure your existing ballast is compatible with JESLED Type A LED tubes. Incompatible ballasts may cause flickering or damage.
2. Insert LED Tube: Insert the JESLED LED tube into the fixture's sockets, ensuring a secure fit.
3. Restore Power: Turn the power back on at the circuit breaker.

Image: A detailed list of compatible ballasts for JESLED T8 LED tubes, crucial for Type A (Plug & Play) installations.

Method 2: Type B - Ballast Bypass (direct wire)

This method requires rewiring the fixture to bypass the ballast, providing direct power to the LED tubes. This eliminates ballast-related issues and further improves energy efficiency. Professional installation is recommended if you are not familiar with electrical wiring.

1. Turn off power: Ensure the power supply to the fixture is completely disconnected at the circuit breaker.
2. Remove Ballast: Locate and remove the existing ballast from the fixture. Disconnect all wires connected to the ballast.
3. Rewire the Fixture: Connect the live (usually black) wire from the power supply to one end of the fixture's lamp holders (pins), and the neutral (usually white) wire to the other end's lamp holders (pins). Ensure the LED tube is designed for dual-ended power.
4. Insert LED Tube: Insert the JESLED LED tube into the rewired fixture's sockets.
5. Restore Power: Turn the power back on at the circuit breaker.

Image: Wiring diagrams for both Type A (Plug & Play with Ballast) and Type B (Ballast Bypass) installations. Note the caution regarding turning off power and dual-ended power for Type B.

Operating Instructions

Once installed, operating the JESLED LED Tube Light is straightforward:

• Power On/Off: Use the standard wall switch connected to your lighting fixture to turn the lights on or off.
• The LED tubes provide instant full brightness upon activation.

Image: A JESLED T8 LED tube light installed in a kitchen, demonstrating its illumination in a typical home environment.

Maintenance

The JESLED LED Tube Lights are designed for long-term, low-maintenance operation. Follow these simple guidelines to ensure optimal performance:

• Cleaning: Ensure the power is off before cleaning. Gently wipe the tubes with a soft, dry, or slightly damp cloth. Do not use harsh chemicals or abrasive cleaners.
• Inspection: Periodically check the tubes and fixture for any signs of damage or loose connections. If any issues are found, disconnect power and address them promptly.
• Replacement: Due to their long lifespan, frequent replacement is not typically required. If a tube needs replacement, ensure the power is off and replace it with another JESLED 24-Inch T8 LED Tube Light of the same type (Type A or Type B).

Troubleshooting

If you encounter issues with your JESLED LED Tube Light, refer to the following troubleshooting steps:

If these steps do not resolve the issue, please contact JESLED customer support for further assistance.

Specifications

Detailed specifications for the JESLED 24-Inch T8 LED Tube Light:

Warranty and Support

JESLED is committed to providing high-quality products and excellent customer service.

• Warranty: This product is covered by a 3-Year JESLED Care manufacturer's warranty, which includes a 36-Month Care Plan.
• Exchange Service: A 30-Day Exchange Service is available for eligible products.
• Customer Support: For any questions, technical assistance, or warranty claims, please contact our 7*24H After-sales Service.

Please refer to the official JESLED website or your purchase documentation for specific contact details and full warranty terms.

Image: JESLED customer support information, detailing available services and warranty periods.