ICM Controls ICM2812-KIT

ICM Controls ICM2812-KIT Universal Furnace Control Board Kit Instruction Manual

Model: ICM2812-KIT

1. Introduction

This manual provides instructions for the installation, operation, and maintenance of the ICM Controls ICM2812-KIT Universal Furnace Control Board Kit. This microprocessor-based control board is designed to replace a wide range of furnace control boards, including the White-Rodgers 50M56U-843 and over 200 other OEM models. It is compatible with Hot Surface Ignition (HSI) systems and is suitable for residential and light commercial applications.

2. Safety Information

WARNING: Risk of electric shock and property damage. Installation and servicing of this product must be performed by a qualified HVAC technician or licensed electrician. Failure to follow these instructions could result in serious injury or death.

  • Always disconnect power to the furnace before installing or servicing the control board.
  • Verify all wiring connections are secure and correct before restoring power.
  • Ensure proper grounding of the furnace system.
  • Do not bypass any safety devices.
  • Wear appropriate personal protective equipment (PPE).
Electrical hazard symbol indicating professional installation is required

Image: Electrical hazard symbol. This symbol indicates that installation requires a professional or qualified person due to electrical risks.

3. Product Overview and Package Contents

The ICM2812-KIT includes a universal furnace control board and a set of wiring harnesses designed for broad compatibility. This kit facilitates the replacement of various OEM furnace control boards.

ICM Controls ICM2812-KIT Universal Furnace Control Board with included wiring harnesses

Image: The ICM2812-KIT Universal Furnace Control Board shown with its accompanying bundle of multi-colored wiring harnesses.

Package Contents:

  • ICM2812 Universal Furnace Control Board
  • Multiple Wiring Harnesses for various furnace models

4. Specifications

  • Model Number: ICM2812-KIT
  • Input Voltage: 24 VAC
  • Ignition Type: Hot Surface Ignition (HSI)
  • Compatibility: Replaces White-Rodgers 50M56U-843 and over 200 OEM models (e.g., Goodman, Carrier, Lennox, Trane, York, Rheem, Nordyne)
  • Fuel Type: Compatible with LP or Natural Gas
  • Operating Temperature Range: -40°F to 176°F (-40°C to 80°C)
  • Humidity: Up to 95% relative humidity (non-condensing)
  • Safety Features: 100% lockout safety feature, monitors timing, trial for ignition, system switches, flame sensing, and lockout.
  • Dimensions: Approximately 9.12 x 9.87 x 2.62 inches
  • Weight: Approximately 1.65 Pounds
  • Manufacturer: ICM Controls

5. Installation Instructions

This section outlines the general steps for installing the ICM2812-KIT. Always refer to the specific wiring diagrams provided with your furnace and the control board for detailed connections.

Preparation:

  1. Disconnect Power: Turn off all electrical power to the furnace at the main service panel. Verify power is off using a voltage meter.
  2. Access Control Board: Open the furnace access panel to locate the existing control board.
  3. Document Wiring: Take clear photographs or make a detailed diagram of all existing wiring connections to the old control board. Label each wire for easy identification.

Replacement Steps:

  1. Remove Old Board: Carefully disconnect all wires from the old control board and remove it from the furnace.
  2. Select Harness: Identify the appropriate wiring harness from the ICM2812-KIT that matches your furnace's existing wiring configuration.
  3. Install New Board: Mount the ICM2812-KIT control board in the same location as the old board, ensuring it is securely fastened.
  4. Connect Wiring: Using your documented wiring diagram, connect the appropriate wires from the furnace to the new ICM2812-KIT control board via the selected harness. Ensure all connections are tight and correct.
  5. Verify Connections: Double-check all wiring against the furnace and control board diagrams. Pay close attention to line voltage, low voltage, and accessory connections.
  6. Close Access Panel: Securely close the furnace access panel.

Post-Installation:

  1. Restore Power: Turn on the electrical power to the furnace at the main service panel.
  2. Test Operation: Initiate a call for heat or cool from the thermostat to verify proper furnace operation. Observe the diagnostic LEDs on the control board.

6. Operation

The ICM2812-KIT is a microprocessor-based control board that manages the essential functions of your furnace. It continuously monitors and controls:

  • Ignition Sequence: Manages the timing and trial for ignition.
  • Flame Sensing: Detects the presence of a flame to ensure safe operation.
  • Blower Motor Timing: Controls the operation of the furnace's blower motor.
  • System Switches: Monitors various safety and operational switches.
  • Lockout Functions: Implements a 100% lockout safety feature in case of ignition failure or other faults.

The board is designed for compatibility with both Liquid Propane (LP) and Natural Gas furnace systems.

7. Diagnostic Features

The ICM2812-KIT features built-in LED diagnostic indicators to assist with troubleshooting. These LEDs flash specific codes to indicate the operational status or identify fault conditions. Refer to the label on the control board itself for a detailed list of diagnostic flash codes.

Common Diagnostic Indicators:

  • Steady ON: Normal operation or specific status (refer to board label).
  • Slow Flash: Indicates a specific operational state or minor fault.
  • Fast Flash: Typically indicates a fault condition requiring attention.

Always consult the diagnostic code legend printed directly on the ICM2812 control board for precise interpretation of the LED flashes.

8. Troubleshooting

When a furnace malfunction occurs, the diagnostic LEDs on the ICM2812-KIT can provide valuable information. Follow these general troubleshooting steps:

  1. Observe LED Codes: Note the flash pattern of the diagnostic LEDs on the control board.
  2. Consult Legend: Refer to the diagnostic code legend printed on the control board to identify the meaning of the observed flash code.
  3. Address Indicated Fault: Based on the code, investigate the corresponding component or system. For example, an ignition lockout code would direct attention to the ignitor, gas valve, or flame sensor.
  4. Reset Power: For some fault conditions, cycling the power (turning off and then on at the main service panel) may reset the board. If the fault persists, further investigation is required.
  5. Professional Assistance: If you are unable to diagnose or resolve the issue, contact a qualified HVAC technician.

9. Maintenance

The ICM2812-KIT control board itself requires no routine maintenance. However, regular maintenance of the overall furnace system is crucial for its longevity and efficient operation. This includes:

  • Annual inspection and cleaning by a qualified technician.
  • Regular replacement of air filters.
  • Checking and cleaning of the flame sensor and ignitor.
  • Ensuring proper ventilation and clear exhaust pathways.

10. Warranty and Support

For warranty information or technical support regarding your ICM Controls ICM2812-KIT, please contact ICM Controls directly. Details for contacting customer support can typically be found on the manufacturer's website or product packaging.

Manufacturer: ICM Controls

Website: www.icmcontrols.com (Example link, verify actual manufacturer website)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.