Ambition Soldier Max Rotary Tattoo Machine User Manual

Introduction

This manual provides detailed instructions for the safe and efficient operation of your Ambition Soldier Max Rotary Tattoo Machine. Please read this manual thoroughly before using the device to ensure proper function and longevity.

Package Contents

• 1x Ambition Soldier Max Tattoo Pen (2400 mAh battery capacity)
• 1x Additional Battery (1800 mAh battery capacity)
• 1x Additional 4.0 mm Stroke Cam
• 1x RCA Adapter
• 1x USB Fast Charging Data Cable
• 1x Storage Box

Setup

Charging the Battery

Before initial use, fully charge the battery.

1. Connect the provided USB fast charging data cable to the machine's charging port.
2. Use a 5V/2A charging adapter (not included) for optimal charging.
3. The display will indicate charging status. A full charge for the 2400 mAh battery takes approximately 8-10 hours, and for the 1800 mAh battery, approximately 6-7 hours.

Assembling the Machine

1. Battery Attachment: Align the battery pack with the main body of the tattoo pen and twist gently until securely connected.
2. RCA Adapter (Optional Wired Use): If using a wired power supply, detach the battery pack and connect the RCA adapter to the machine body. Then, connect your RCA cable to the adapter.
3. Needle Cartridge Insertion: Insert a compatible needle cartridge into the front end of the machine, twisting it clockwise until it locks into place.
4. Adjusting Needle Depth: Rotate the grip of the machine to adjust the needle depth as required.

Operating Instructions

Power On/Off and Boot Modes

• Power On: Press and hold the power button (located on the display unit) for a few seconds until the screen illuminates.
• Power Off: Press and hold the power button again until the screen turns off.
• Switching Boot Mode: Double-tap the power button quickly to switch between "Jump Start Mode" (indicated by 'J' on the display) and "Standard Mode" (indicated by 'S').
  • Jump Start Mode (J): Provides an 8V initial boost, useful for pushing larger magnum tattoo needles.
  • Standard Mode (S): Normal startup.

Voltage Adjustment

• Use the "Voltage Increase Key" (+) and "Voltage Reduction Key" (-) buttons on the display unit to adjust the operating voltage. The voltage range is 4-12V.

Work Modes (Frequency & Normal)

• Switching Modes: Long press the "Work Mode Button" (located below the power button) to toggle between "Regular Mode" and "Frequency Mode".
• Frequency Mode: This mode offers 50 different adjustable frequency levels. Use the "Frequency Up Button" and "Frequency Down Button" to select your desired frequency.

Billing Function

The machine features a billing function that automatically calculates the total charge based on working hours.

• The display shows the timer and calculated charge.
• Adjust the charge amount per minute using the "Billing Up Button" and "Billing Down Button" (these are typically integrated with the frequency buttons, requiring a mode switch).

Maintenance

Cleaning

The Ambition Soldier Max tattoo machine is designed for easy disassembly, allowing for thorough cleaning of each component.

1. Ensure the machine is powered off and disconnected from any power source.
2. Carefully disassemble the machine by unscrewing the battery pack/RCA adapter and the grip section.
3. Clean all external surfaces with a suitable disinfectant wipe.
4. For internal components, follow professional sterilization guidelines for tattoo equipment. Avoid immersing the motor or electronic components in liquid.
5. Ensure all parts are completely dry before reassembly.

Storage

Store the machine in its original box or a clean, dry, and sterile environment when not in use. Keep it away from direct sunlight, extreme temperatures, and moisture.

Troubleshooting

• Machine Not Turning On:
  • Ensure the battery is fully charged.
  • Check that the battery pack is securely attached.
  • If using the RCA adapter, ensure it is properly connected and the power supply is functional.
• Inconsistent Operation/Power:
  • Verify the battery charge level.
  • Check for any loose connections between components.
  • Ensure the needle cartridge is correctly inserted and not jammed.
• Display Issues:
  • Restart the machine.
  • Ensure the battery is adequately charged.

If problems persist, please contact customer support.

Specifications

Warranty and Support

For warranty information or technical support, please refer to the documentation included with your purchase or contact Ambition customer service directly.

Return Policy: The product typically comes with a 30-day refund/replacement policy. Please check your purchase details for specific terms.