1. Introduction
This manual provides essential instructions for the safe and efficient setup, operation, and maintenance of your WAVE Garda 4 Person Eco Foam Hot Tub. Please read this manual thoroughly before installation and use to ensure proper function and to prevent injury or damage. Keep this manual for future reference.
2. Important Safety Information
Always follow basic safety precautions when using electrical products, especially when children are present. Failure to follow these instructions could result in injury or death.
- Read all instructions: Before installing and using this hot tub, read, understand, and follow all instructions in this manual.
- Electrical Safety: Connect the hot tub only to a grounded outlet protected by a Ground Fault Circuit Interrupter (GFCI). Do not use extension cords.
- Water Temperature: The water temperature in a hot tub should not exceed 104°F (40°C). Lower temperatures are recommended for prolonged use.
- Children: Supervise children at all times. Keep the hot tub covered when not in use.
- Health Conditions: Consult a physician before use if you have any health conditions, are pregnant, or are taking medication.
- Chemicals: Handle hot tub chemicals with care and store them out of reach of children.
- Assembly: Ensure the hot tub is assembled on a flat, stable surface capable of supporting its weight when filled.
3. Package Contents
Verify that all components are present before beginning assembly:
- WAVE Garda Hot Tub Liner
- Eco Foam Panels (for exterior structure)
- Integrated Heater and Pump Unit
- Protective Cover with Safety Clips
- Wired Control Panel
- Filter Cartridges
- Drain Hose Adapter
- Instruction Manual
4. Setup Instructions
The WAVE Garda Hot Tub is designed for quick and easy, tool-free setup, typically completed within 20-30 minutes.
4.1 Site Preparation
- Choose a flat, level surface that can safely support the hot tub when filled (approximately 218 gallons / 825 liters of water plus occupants).
- Ensure the location is near a grounded electrical outlet (GFCI protected) and a water source.
- Clear the area of any sharp objects or debris.
4.2 Assembly Steps
- Unpack all components and lay them out on the prepared surface.
- Assemble the Eco Foam panels to form the outer structure of the hot tub. The panels interlock for a secure fit.
- Carefully place the hot tub liner inside the assembled foam structure, ensuring it is centered and smooth.
- Connect the integrated heater and pump unit to the designated ports on the hot tub liner. Ensure all connections are tight to prevent leaks.
- Install the filter cartridge into the filter housing within the hot tub.
- Fill the hot tub with water to the recommended fill line.
- Connect the power cord to a GFCI-protected electrical outlet.
- Place the protective cover over the hot tub and secure it with the safety clips.
Figure 1: The fully assembled WAVE Garda 4 Person Eco Foam Hot Tub in Pebble White, showcasing its square shape and textured exterior.
Figure 2: The hot tub is shown with its insulated cover securely fastened, highlighting the cover's design for heat retention and protection.
Figure 3: An exploded diagram reveals the internal construction of the hot tub, detailing the integrated heater, energy-saving cover, efficient Wave Eco Foam Core, and portable design. It also highlights the safe plug-and-play power cable and changeable outer cover.
5. Operating Instructions
Your WAVE Garda Hot Tub features a user-friendly wired control panel for managing its functions.
5.1 Power On/Off
- Press the power button on the wired control panel to turn the hot tub on or off.
5.2 Rapid Heating System
- Use the temperature control buttons on the panel to set your desired water temperature, up to 104°F (40°C).
- The integrated heater will automatically work to reach and maintain the set temperature. Heating rate is approximately 1°C per hour.
5.3 AquaJet Massage System
- Press the bubble button on the control panel to activate the 70 AquaJet Massage System.
- Press the button again to turn off the massage function.
5.4 Wi-Fi Control
- Download the official WAVE app on your smartphone or tablet.
- Follow the in-app instructions to connect your hot tub to your home Wi-Fi network.
- Once connected, you can control heating, filtration, and massage functions remotely.
6. Maintenance
Regular maintenance ensures the longevity and hygienic operation of your hot tub.
6.1 Filtration System
- The hot tub features an easy-to-use filtration system.
- Clean filter cartridges regularly (e.g., weekly) by rinsing them with a hose.
- Replace filter cartridges every 1-2 months, or more frequently depending on usage and water quality.
6.2 Water Care
- Test water chemistry regularly (e.g., 2-3 times per week) using test strips.
- Maintain appropriate levels of sanitizers (e.g., chlorine or bromine), pH, and alkalinity.
- Drain and refill the hot tub every 3-4 months, or as needed, to ensure fresh water.
6.3 Cleaning the Hot Tub
- Wipe down the interior surface of the hot tub with a soft cloth and mild cleaner when drained.
- Clean the exterior panels as needed with a damp cloth.
7. Troubleshooting
Refer to the table below for common issues and their solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Hot tub not heating | Power supply issue, heater malfunction, low water level, dirty filter. | Check power connection and GFCI. Ensure water level is adequate. Clean or replace filter. Contact customer support if issue persists. |
| Water is cloudy | Dirty filter, improper water chemistry, heavy usage. | Clean or replace filter. Test and adjust water chemistry (sanitizer, pH). Shock the water if necessary. |
| Bubbles are weak or not working | Air blower obstruction, pump issue. | Ensure air intake is clear. Check for error codes on control panel. Contact customer support. |
| Water leaking | Loose connections, liner puncture. | Check all hose connections and tighten. Inspect liner for damage and repair if possible. Contact customer support for significant leaks. |
| Wi-Fi connection issues | Incorrect Wi-Fi password, router distance, app issues. | Verify Wi-Fi password. Move hot tub closer to router or use a Wi-Fi extender. Reinstall the app. |
8. Specifications
Detailed technical specifications for the WAVE Garda 4 Person Eco Foam Hot Tub.
Figure 4: This graphic provides key product specifications such as dimensions, water capacity, seating capacity, and features like advanced filtration, 70/90 bubble jet massage system, heating, and Wi-Fi control. It also shows the wired controller and available color options.
| Feature | Specification |
|---|---|
| Brand | WAVE |
| Model Name | GAR4PEBRATUS |
| Product Dimensions | 63"L x 63"W x 27"H (160cm x 160cm x 70cm) |
| Material | Woven UV-protected PVC construction with PU-insulated foam core |
| Shape | Square |
| Capacity | 218 Gallons (825 Liters) |
| Seating Capacity | 4 Persons |
| Number of Jets | 70 AquaJet Massage System |
| Heating System | Integrated Heater, up to 104°F (40°C), approx. 1°C/hour heating rate |
| Control | Wired Control Panel, Wi-Fi App Control |
| Assembly Required | Yes (Tool-free, approx. 20-30 minutes) |
| GTIN | 05061039891927 |
| ASIN | B0D3HX2TR4 |
9. Warranty and Support
For warranty information, product registration, or technical support, please refer to the warranty card included with your purchase or visit the official WAVE website. Contact details for customer service can typically be found on the manufacturer's website or within your purchase documentation.
