lightmaXX LS-6 Steel Light Stand Instruction Manual

1. Introduction

Thank you for choosing the lightmaXX LS-6 Steel Light Stand. This manual provides essential information for the safe and efficient assembly, operation, and maintenance of your light stand. Please read these instructions carefully before use and retain them for future reference.

The lightmaXX LS-6 is a robust steel light stand designed for professional use, capable of supporting lighting fixtures up to 70 kg. Its sturdy construction ensures stability and reliability for various stage, studio, or event setups.

2. Safety Instructions

• Always ensure the stand is placed on a stable, level surface.
• Do not exceed the maximum load capacity of 70 kg. Overloading can cause instability and damage.
• Distribute weight evenly on the crossbar.
• Ensure all locking mechanisms (knobs, clamps) are securely tightened before and during use.
• Keep hands and fingers clear of moving parts during assembly and adjustment to prevent pinching.
• Do not leave the stand unattended with heavy equipment, especially in areas with high foot traffic or wind.
• Regularly inspect the stand for any signs of wear, damage, or loose components. Do not use if damaged.
• Avoid exposing the stand to extreme weather conditions or corrosive substances.

3. Package Contents

Please check that all components are present and undamaged upon unpacking:

• 1x lightmaXX LS-6 Main Stand Assembly
• 1x Crossbar/T-Bar (if included as separate piece)
• Necessary mounting hardware (bolts, washers, wing nuts)

If any parts are missing or damaged, please contact your retailer immediately.

Figure 3.1: Included assembly hardware, featuring bolts, washers, and wing nuts.

4. Setup Instructions

Follow these steps to assemble and set up your lightmaXX LS-6 stand:

1. Unfold the Base: Carefully spread the legs of the stand until they are fully extended and locked into position. Ensure the base is stable and balanced.


Figure 4.1: The robust base mechanism with fully extended legs, secured by a tightening knob for stability.

2. Adjust Height: Loosen the height adjustment knob on the main pole. Carefully extend the upper section(s) to the desired height. Once at the desired height, securely tighten the knob to prevent slippage.
3. Attach Crossbar: If your crossbar is separate, align it with the mounting point at the top of the stand. Use the provided bolts, washers, and wing nuts to securely fasten the crossbar to the stand. Ensure all connections are tight.

Figure 4.2: The top clamp mechanism, illustrating how the crossbar attaches to the main pole with securing bolts.
4. Mount Lighting Fixtures: Attach your lighting fixtures to the crossbar using appropriate clamps or mounting hardware (not included). Distribute the weight evenly across the crossbar.

5. Operating Instructions

To operate your lightmaXX LS-6 stand effectively:

• Height Adjustment: To change the height, always support the upper section of the stand with one hand while loosening the adjustment knob with the other. Slowly raise or lower the section to the desired height, then firmly tighten the knob.
• Load Distribution: When mounting multiple fixtures, try to balance the weight symmetrically on the crossbar to maintain optimal stability.
• Stability Check: Before leaving the stand unattended, gently push on it from different directions to confirm its stability. If it wobbles, re-check leg extension and locking mechanisms.
• Transport: Before moving the stand, remove all attached equipment, fully retract the height sections, and fold the legs. This prevents damage and makes transport safer.

6. Maintenance

Proper maintenance will extend the life of your light stand:

• Cleaning: Wipe down the stand with a soft, damp cloth to remove dust and dirt. Avoid abrasive cleaners or solvents.
• Lubrication: Periodically apply a small amount of silicone-based lubricant to the sliding sections to ensure smooth height adjustment. Do not over-lubricate.
• Inspection: Regularly check all bolts, nuts, and locking mechanisms for tightness. Inspect the steel tubing for any dents, bends, or corrosion.
• Storage: Store the stand in a dry, cool place, preferably in a protective bag or case, to prevent dust accumulation and potential damage.

7. Troubleshooting

Here are some common issues and their solutions:

• Stand is wobbly:
  • Ensure legs are fully extended and locked.
  • Verify the stand is on a level surface.
  • Check that all height adjustment knobs are securely tightened.
• Height adjustment is stiff:
  • Clean the sliding sections to remove dirt.
  • Apply a small amount of silicone lubricant to the sliding surfaces.
• Crossbar feels loose:
  • Tighten all bolts and wing nuts securing the crossbar to the main stand.

8. Specifications

• Model: lightmaXX LS-6
• Material: Steel
• Maximum Load Capacity: 70 kg
• Product Dimensions: 140 x 17 x 13.5 cm (folded/packaged)
• Item Weight: 6.6 kg
• Manufacturer Reference: LIG0018620-000

9. Warranty and Support

This lightmaXX LS-6 Steel Light Stand comes with a standard manufacturer's warranty. Please refer to the warranty card included with your purchase or visit the official lightmaXX website for detailed warranty terms and conditions.

For technical support, spare parts, or service inquiries, please contact your authorized lightmaXX dealer or the lightmaXX customer service department. Contact information can typically be found on the manufacturer's website or your purchase documentation.