Sylvania A19 LED Light Bulbs Instruction Manual

1. Introduction

Thank you for choosing Sylvania A19 LED Light Bulbs. This manual provides essential information for the safe installation, operation, and maintenance of your new LED bulbs. Please read these instructions carefully before use and retain them for future reference.

2. Product Overview

This package includes a combination of Sylvania A19 LED light bulbs designed to replace traditional incandescent bulbs. You will find both 40W equivalent (6W, 450 lumens) and 60W equivalent (8.5W, 800 lumens) bulbs, all featuring a soft white (2700K) color temperature and a standard medium (E26) base.

Image 1: Sylvania A19 LED Light Bulbs, showing both 40W and 60W equivalent bulbs in their packaging.

These energy-efficient bulbs offer instant illumination, long lifespan, and are free from UV/IR emissions, mercury, and lead.

3. Safety Information

• Risk of Electric Shock: Always turn off power to the fixture before inspecting, installing, or removing the bulb.
• Indoor Use Only: These bulbs are designed for indoor use in dry locations. Do not use in wet or damp environments unless the fixture is specifically rated for such conditions.
• Not for Enclosed Fixtures: Avoid using these bulbs in fully enclosed fixtures, as this can shorten their lifespan due to heat buildup.
• Non-Dimmable: These bulbs are non-dimmable. Do not use with dimmer switches, as this may cause damage to the bulb or dimmer.
• Operating Temperature: Suitable for operation in temperatures between -20°C and +40°C (-4°F and +104°F).
• Weight: Do not use in fixtures where the bulb's weight might exceed the fixture's capacity.

4. Setup and Installation

Installation of Sylvania A19 LED light bulbs is straightforward. Follow these steps:

1. Turn Off Power: Locate the light switch or circuit breaker controlling the fixture and turn off the power completely.
2. Remove Old Bulb: Carefully unscrew the existing light bulb from the fixture. Allow it to cool if it has been recently in use.
3. Insert New LED Bulb: Gently screw the Sylvania A19 LED bulb into the socket until it is snug. Do not overtighten.
4. Restore Power: Turn the power back on at the switch or circuit breaker.
5. Test: Turn on the light switch to ensure the bulb illuminates correctly.

Image 2: A set of four Sylvania A19 LED light bulbs, ready for installation.

5. Operating Instructions

Sylvania A19 LED light bulbs operate like traditional bulbs. Once installed, simply use the wall switch or fixture switch to turn the light on or off. These bulbs provide instant full brightness with no warm-up time.

6. Maintenance

These LED bulbs require minimal maintenance due to their long lifespan of up to 11,000 hours.

• Cleaning: To clean the bulb, ensure the power is off and the bulb is cool. Wipe gently with a soft, dry cloth. Do not use liquid cleaners or abrasive materials.
• Replacement: When the bulb reaches the end of its life, follow the installation steps in Section 4 to replace it with a new Sylvania A19 LED bulb. Dispose of old bulbs according to local regulations.

7. Troubleshooting

If your Sylvania A19 LED bulb does not light up after installation, consider the following:

• No Power: Check if the light switch is in the 'ON' position. Verify that the circuit breaker for the fixture has not tripped.
• Loose Connection: Turn off the power, then carefully re-screw the bulb into the socket to ensure a secure connection.
• Incorrect Fixture: Ensure the fixture is compatible with A19 bulbs and has a medium (E26) base.
• Dimmer Switch: Confirm that the fixture is not connected to a dimmer switch, as these non-dimmable bulbs are not compatible.
• Damaged Bulb: If the above steps do not resolve the issue, the bulb may be faulty. Replace it with a new one.

8. Specifications

9. Warranty and Support

For warranty information or technical support, please refer to the packaging or contact LEDVANCE customer service directly. Keep your purchase receipt as proof of purchase.