1. Introduction
This instruction manual provides detailed information on the installation, operation, and maintenance of your Xnbada T8K Music+DMX Console LED Controller. Please read this manual thoroughly before using the device to ensure proper functionality and safety.
The T8K Music+DMX Console is designed for controlling RGB SPI-TTL LED strip lights, offering advanced features such as DMX512 compatibility, audio input for music synchronization, and 8-channel output for extensive pixel control.
2. Safety Information
- Ensure the power supply voltage matches the controller's requirements (AC110V-220V).
- Do not expose the device to moisture or extreme temperatures.
- Disconnect power before making any connections or performing maintenance.
- Avoid direct contact with internal components. Refer servicing to qualified personnel.
- Keep out of reach of children.
3. Product Overview
The Xnbada T8K Music+DMX Console LED Controller is a versatile device for managing various types of LED lighting. Key features include:
- 32-65536 gray control levels with software Gamma correction.
- Support for point, line, and area light sources, including various rules and shaped processing.
- 8 output ports, each supporting up to 1024 pixels.
- Integrated MIC (Mic in) and headphone audio input (Aux in) with adjustable sensitivity.
- Supports up to 80 programs for loop playback.
3.1. Component Identification (Rear Panel)
Figure 1: Rear panel of the T8K LED Controller, showing DMX512 IN/OUT, DMXIN/DMXOUT, SPI-TTL DATA OUT, SYNCIN/SYNCOUT, PowerIN (AC110V-220V), and On/Off switch.
- DMX512 IN/OUT: XLR 3-pin connectors for DMX signal input and output.
- DMXIN/DMXOUT: RJ45 ports for DMX signal input and output.
- SPI-TTL DATA OUT: 8-channel terminal block for connecting SPI-TTL LED strips.
- SYNCIN/SYNCOUT: RJ45 ports for synchronization with other controllers.
- PowerIN AC110V-220V: Power input socket.
- On/Off: Power switch for the unit.
3.2. Component Identification (Front Panel)
Figure 2: Front panel of the T8K LED Controller, showing Parameter Display, keystroke buttons, SD card slot, Indicator Light, and Music Adjust knob.
- Parameter Display: Digital display for showing current settings and program numbers.
- Keystroke Buttons: Buttons for navigating menus and adjusting parameters (Set, Speed, Mode).
- SD Card Slot: For inserting an SD card containing program files.
- Indicator Light: Status indicator.
- Music Adjust: Knob to adjust the sensitivity of audio input (Mic in/Aux in).
- Mic in/Aux in: Audio input ports for music synchronization.
3.3. Supported LED Types
Figure 3: The T8K LED Controller supports various SPI-TTL LED types, including WS2811, WS2812B, WS2813, and WS2815 LED strip lights.
4. Setup
4.1. Power Connection
- Ensure the controller's power switch is in the OFF position.
- Connect the AC power cable to the PowerIN AC110V-220V socket on the rear panel.
- Plug the other end of the power cable into a suitable AC power outlet.
4.2. LED Strip Connection (SPI-TTL Data Out)
The controller features 8 SPI-TTL data output ports. Each port can control up to 1024 pixels. Refer to the wiring diagram for proper connection.
Figure 4: T8K LED Controller highlighting the 8 port outputs and the Music Adjust knob.
- Identify the Data (DAT), Clock (CLK), and Ground (GND) wires on your SPI-TTL LED strip.
- Connect the corresponding wires from your LED strip to the SPI-TTL DATA OUT terminal block on the controller. Ensure correct polarity and port assignment.
- For multiple strips, use separate output ports for each strip or segment as required by your lighting design.
4.3. DMX Connection (Optional)
If integrating with a DMX system, use the DMX512 IN/OUT (XLR) or DMXIN/DMXOUT (RJ45) ports.
- Connect the DMX output from your DMX console to the DMX512 IN port on the controller.
- If daisy-chaining multiple DMX devices, connect the DMX512 OUT port to the next device's DMX IN.
4.4. Audio Input Connection (Optional)
For music synchronization, connect an audio source to the Mic in or Aux in ports.
- Connect a microphone to the Mic in port for ambient sound detection.
- Connect an audio player (e.g., phone, media player) to the Aux in port using a 3.5mm audio cable.
4.5. SD Card Insertion
The controller uses an SD card to store program files. Ensure the SD card is properly formatted and contains compatible program files.
- Locate the SD card slot on the front panel.
- Insert the SD card gently until it clicks into place.
4.6. Typical Wiring Diagram
Figure 5: Example wiring diagram illustrating connections for the T8K LED Controller with LED strips and power supply.
5. Operating Instructions
5.1. Power On/Off
- To power on, flip the On/Off switch on the rear panel to the 'On' position. The Parameter Display will light up.
- To power off, flip the On/Off switch to the 'Off' position.
5.2. Program Selection
Use the keystroke buttons (Set, Speed, Mode) on the front panel to navigate and select programs stored on the SD card.
- Press the 'Mode' button to cycle through available programs. The program number will be shown on the Parameter Display.
- Press 'Set' to confirm a selection or enter a setting mode.
- Use 'Speed' to adjust the playback speed of dynamic programs.
5.3. Music Synchronization
When an audio source is connected, the controller can synchronize lighting effects with music.
- Rotate the 'Music Adjust' knob on the front panel to increase or decrease the sensitivity of the audio input. Adjust until the lighting effects respond appropriately to the music's beat.
5.4. DMX Control
When connected to a DMX console, the T8K controller can receive DMX signals to control the LED outputs.
- Ensure the DMX input is correctly connected.
- Configure the DMX address and channel assignments on your DMX console according to the controller's DMX protocol (refer to advanced settings or software documentation if applicable).
6. Specifications
Figure 6: T8K LED Controller dimensions and technical specifications.
| Feature | Specification |
|---|---|
| Model | T8K Music+DMX512 |
| Operating Voltage | AC110V-220V |
| Rated Power | 2W |
| Control Range | 1-8192 pixels (total) |
| Working Temperature | -30°C to 85°C |
| Signal Output Ports | 8 TTL data outputs |
| Pixels per Port | Up to 1024 pixels (1 chip = 1 pixel) |
| Gray Control Levels | 32-65536 levels |
| Item Weight | 2.75 pounds |
| Product Dimensions (L*W*H) | 290mm * 150mm * 45mm (approx. 11.4 x 5.9 x 1.8 inches) |
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power | Power cable disconnected; Power switch off; No power from outlet. | Check power cable connection; Ensure power switch is ON; Test outlet with another device. |
| LEDs not lighting up | Incorrect wiring (Data, Clock, GND); Faulty LED strip; Incorrect program selected; SD card error. | Verify all wiring connections and polarity; Test LED strip separately; Select a different program; Reformat or replace SD card. |
| Music sync not working | Audio cable disconnected; Music Adjust knob too low; No audio input. | Check audio cable connection; Increase Music Adjust sensitivity; Ensure audio source is playing. |
| DMX control issues | Incorrect DMX wiring; Wrong DMX address; DMX console not sending signal. | Verify DMX cable connections; Check DMX address settings; Confirm DMX console is operational. |
8. Maintenance
- Cleaning: Use a soft, dry cloth to clean the exterior of the controller. Do not use liquid cleaners or solvents.
- Storage: Store the controller in a cool, dry place away from direct sunlight and extreme temperatures when not in use.
- Firmware Updates: Check the manufacturer's website for any available firmware updates for improved performance or new features.
9. Warranty and Support
For warranty information and technical support, please refer to the documentation provided with your purchase or contact Xnbada customer service. Keep your purchase receipt for warranty claims.
Manufacturer: Xnbada