TECKNET Wireless Doorbell User Manual

Introduction

Thank you for purchasing the TECKNET Wireless Doorbell. This self-powered, IP65 waterproof doorbell system offers convenience and reliability for your home or office. Featuring a plug-through receiver, 60 chimes, 5 volume levels, and a bright RGB light indicator, it is designed for ease of use and accessibility. Please read this manual carefully before installation and operation to ensure optimal performance and safety.

Safety Information

• Do not expose the receiver to water or excessive humidity. The transmitter is IP65 waterproof, but the receiver is for indoor use only.
• Do not disassemble or attempt to repair the device. Refer all servicing to qualified personnel.
• Ensure the power outlet for the receiver is easily accessible.
• Keep the device away from direct heat sources and open flames.
• Use only as intended for a doorbell system.

Package Contents

Please check the package contents to ensure all items are present:

• 1 x Self-Powered Transmitter (Push Button)
• 1 x Plug-Through Receiver (Chime Unit)
• 1 x Double-Sided Adhesive Tape
• 1 x User Manual

Product Overview

Image: The TECKNET Wireless Doorbell system, showing the self-powered transmitter on the left and the plug-through receiver on the right. The receiver features a speaker grille with an RGB light ring and a pass-through power socket. The transmitter has a bell icon and a blue indicator light.

Transmitter (Push Button)

• Self-Powered: Generates its own electricity when pressed, requiring no batteries.
• IP65 Waterproof: Designed to withstand various weather conditions.
• Indicator Light: Illuminates when pressed to confirm signal transmission.

Receiver (Chime Unit)

• Plug-Through Design: Allows you to use the wall socket even when the doorbell is plugged in.
• RGB Light Indicator: Provides visual alerts, ideal for the hearing impaired.
• Speaker: Emits the selected chime sound.
• Volume Button: Adjusts the volume level.
• Melody Button: Cycles through available chimes.

Setup

1. Plug in the Receiver: Insert the receiver into a standard wall socket in your desired location. Ensure the socket is easily accessible.
2. Pairing (Pre-paired from factory): The transmitter and receiver are typically pre-paired at the factory. If they do not connect automatically, or if you wish to pair additional transmitters/receivers, follow these steps:
   • Plug in the receiver.
   • Press and hold the volume button on the receiver for approximately 5 seconds until the RGB light flashes rapidly. This indicates pairing mode.
   • Immediately press the transmitter button. The receiver will chime and the RGB light will stop flashing, indicating successful pairing.
3. Mount the Transmitter:
   • Clean the surface where you intend to mount the transmitter. Ensure it is dry and free of dust.
   • Peel off one side of the double-sided adhesive tape and apply it firmly to the back of the transmitter.
   • Peel off the other side of the tape and firmly press the transmitter onto the desired mounting surface (e.g., door frame, wall). Hold for 30 seconds to ensure strong adhesion.
   • Alternatively, you can use screws (not included) to mount the transmitter through the designated screw holes if preferred.
4. Test the Doorbell: Press the transmitter button to ensure the receiver chimes and the RGB light activates.

Operating Instructions

Changing Chimes

The doorbell offers 60 different chimes. To change the chime:

• Press the "Melody" button (music note icon) on the side of the receiver to cycle through the available chimes.
• Once you hear a chime you like, stop pressing the button. The receiver will remember your selection.

Adjusting Volume

There are 5 adjustable volume levels (0-120 dB). To adjust the volume:

• Press the "Volume" button (speaker icon) on the side of the receiver to cycle through the volume levels.
• Level 0 is mute. The receiver will remember your chosen volume setting.

Using the Plug-Through Socket

The receiver features a pass-through socket, allowing you to plug another appliance into it without losing a power outlet. Simply plug your appliance directly into the socket on the front of the receiver.

Maintenance

• Cleaning: Wipe the doorbell units with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Weather Resistance: The transmitter is IP65 waterproof and designed for outdoor use. However, avoid submerging it in water.
• Temperature Range: The system operates effectively between -20°C to 60°C (-4°F to 140°F).

Troubleshooting

Specifications

Warranty and Support

TECKNET products come with a standard warranty. For detailed warranty information, please refer to the warranty card included with your purchase or visit the official TECKNET website. If you encounter any problems in using the product, please contact our professional customer service team for assistance. You can typically find contact information on the product packaging or the TECKNET website.

We are committed to providing excellent service and support for our products.