1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Triumph Daytona 660 Heated Grip Kit (MPN A9639102). Designed to enhance riding comfort in cooler conditions, these heated grips feature integrated temperature controls and display settings directly on your motorcycle's instrument screen. Please read this manual thoroughly before installation and use to ensure proper function and safety.
2. Safety Information
Always prioritize safety when working on your motorcycle. Improper installation or use of this product can lead to damage to the motorcycle or personal injury. If you are unsure about any part of the installation process, consult a qualified Triumph technician.
- Ensure the motorcycle's ignition is off and the battery is disconnected before beginning installation.
- Wear appropriate personal protective equipment (PPE) during installation.
- Do not modify the heated grip kit components or wiring.
- Ensure all connections are secure and properly insulated to prevent short circuits.
- Regularly inspect the grips for any signs of wear or damage.
3. Package Contents
Verify that all components are present and undamaged before proceeding with installation.
- Left Heated Grip with Integrated Controls
- Right Heated Grip
- Mounting Hardware
- Wiring Harness
- Installation Instructions (this manual)

Figure 3.1: Image showing the two black heated grips, one with visible internal wiring and control mechanism, ready for installation on a motorcycle handlebar.
4. Setup and Installation
The Triumph Daytona 660 Heated Grip Kit is designed for internal wiring through your handlebars, ensuring a clean and integrated appearance. Professional installation is recommended.
- Preparation: Ensure the motorcycle is on a stable stand. Turn off the ignition and disconnect the battery's negative terminal.
- Remove Existing Grips: Carefully remove the existing handlebar grips. This may involve cutting or sliding them off, depending on their type. Clean the handlebar surfaces thoroughly.
- Route Wiring: The heated grips are designed for internal wiring. Carefully route the wiring harness through the handlebars according to the motorcycle's service manual. Ensure no wires are pinched or stressed.
- Install New Grips: Slide the new heated grips onto the handlebars. The left grip contains the integrated controls. Ensure they are fully seated and oriented correctly. Use a suitable grip adhesive if recommended by Triumph.
- Connect Wiring: Connect the heated grip wiring harness to the motorcycle's electrical system as specified in the Triumph Daytona 660 service manual. Pay close attention to polarity and secure all connections.
- Test Functionality: Reconnect the battery. Turn on the ignition and test the heated grips through their various settings to ensure proper operation and display on the instrument screen.
- Final Inspection: Check all connections and ensure the grips are securely mounted and do not interfere with throttle operation or other controls.
5. Operating Instructions
The Triumph Daytona 660 Heated Grips feature intuitive controls integrated into the left-hand grip, allowing for easy adjustment of heating levels.
- Turning On/Off: Locate the control button on the left grip. Press and hold the button for approximately 2-3 seconds to turn the heated grips on or off.
- Adjusting Temperature: Once on, short presses of the control button will cycle through the available heating levels (e.g., Low, Medium, High).
- Display: The selected heating level will be displayed on your motorcycle's instrument screen, providing clear feedback on the current setting.
- Optimal Use: Start with a lower setting and increase as needed. Avoid using the highest setting for extended periods if not necessary, to conserve battery power.
These grips are designed to keep your hands warm, comfortable, and reaction-ready, even in cool riding conditions.
6. Maintenance
Proper maintenance ensures the longevity and optimal performance of your heated grips.
- Cleaning: Clean the grips regularly with a mild soap and water solution. Avoid harsh chemicals or abrasive cleaners that could damage the rubber material.
- Inspection: Periodically inspect the grips for any signs of wear, cracks, or damage to the rubber or wiring. Ensure the control button operates smoothly.
- Wiring: Check the wiring for any signs of fraying, pinching, or loose connections, especially where it enters the handlebars.
- Storage: If storing the motorcycle for an extended period, ensure the heated grips are turned off.
7. Troubleshooting
If you encounter issues with your heated grips, refer to the following troubleshooting guide:
| Problem | Possible Cause | Solution |
|---|---|---|
| Grips do not heat up. |
|
|
| Grips heat unevenly. |
|
|
| Control button unresponsive. |
|
|
For issues not covered here, or if troubleshooting steps do not resolve the problem, please contact your authorized Triumph dealer.
8. Specifications
- Model: Triumph Daytona 660 Heated Grip Kit
- Part Number (MPN): A9639102
- Compatibility: Triumph Daytona 660 motorcycle
- Material: Rubber
- Color: Black
- Features: Integrated temperature controls, display on motorcycle instrument screen, internal wiring design.
- Included Components: Heated Grips (Left & Right), Mounting Hardware, Wiring Harness.
9. Warranty and Support
This Triumph accessory is covered by the standard Triumph accessory warranty. For specific warranty terms and conditions, please refer to the documentation provided with your motorcycle or contact your authorized Triumph dealer. For technical support, installation assistance, or spare parts, please contact your local authorized Triumph dealership or visit the official Triumph Motorcycles website.
Contact Information:
- Authorized Triumph Dealer: Find a Dealer
- Official Triumph Website: www.triumphmotorcycles.com