Introduction
This manual provides comprehensive instructions for the installation, operation, maintenance, and troubleshooting of your DEWENWILS HRLS11B Remote Control Light Bulb Socket. Please read this manual thoroughly before use to ensure proper function and safety.
Safety Information
- Ensure the power is turned off at the circuit breaker before installing or replacing any light bulb or socket.
- Do not exceed the maximum wattage ratings for bulbs: LED Bulb ≤20W, Incandescent Bulb ≤60W, CFL Bulb ≤20W.
- This device is designed for indoor use in dry locations. Avoid exposure to moisture or extreme temperatures.
- Do not use in enclosed narrow lighting fixtures, with dimmer switches, or with motion detector lights.
- Keep out of reach of children.
Setup Instructions
Package Contents
- 1 x Wireless Light Bulb Socket (E26/E27 base)
- 1 x Wall Mounted Wireless Switch (includes 1 x 12V battery)
Installation Steps
- Prepare the Fixture: Ensure the power to the light fixture is OFF at the circuit breaker. Remove the existing light bulb.
- Install the Socket: Screw the DEWENWILS wireless light bulb socket into the existing E26/E27 light fixture. Ensure it is securely tightened.
- Install the Light Bulb: Screw your desired light bulb (LED ≤20W, Incandescent ≤60W, CFL ≤20W) into the DEWENWILS wireless light bulb socket.
- Mount the Wireless Switch: The wireless switch can be mounted anywhere using screws or double-sided adhesive (not included). Choose a convenient location, such as beside a door or bed. No wiring is required for the switch.
- Restore Power: Turn the power back ON at the circuit breaker.

Pairing Instructions (If needed)
The wireless switch and receiver kit are typically pre-programmed. If re-pairing is necessary or if you wish to pair additional switches/sockets:
- Ensure the light bulb is removed from the socket.
- Press and hold the program button on the light bulb socket until the indicator light flashes.
- While the indicator light is flashing, press the 'ON' or 'OFF' button on the wireless switch you wish to pair.
- The indicator light on the socket will stop flashing, confirming successful pairing.
- Re-insert the light bulb into the socket.

Operating Instructions
Basic Operation
- Press the 'ON' button on the wireless switch to turn the connected light bulb on.
- Press the 'OFF' button on the wireless switch to turn the connected light bulb off.
- The socket also features a manual ON/OFF button for direct control.

Programmable and Expandable Features
The DEWENWILS wireless light switch and receiver kit can be programmed to suit various needs:
- Control Multiple Devices with One Switch: A single wireless switch can be paired with multiple light bulb sockets to control several lights simultaneously.
- Control One Device with Multiple Switches: A single light bulb socket can be paired with multiple wireless switches, allowing control from different locations.

Remote Range
The strong RF signal provides a remote range of up to 100 feet in open areas. This allows control of lights through walls and doors without interference from other appliances.

Maintenance
Battery Replacement (Wireless Switch)
The wireless switch is powered by one 12V battery (included). When the switch's performance degrades, replace the battery. To replace:
- Carefully open the battery compartment on the back of the wireless switch.
- Remove the old 12V battery.
- Insert a new 12V battery, ensuring correct polarity.
- Close the battery compartment.
Cleaning
Wipe the light bulb socket and wireless switch with a dry, soft cloth. Do not use liquid cleaners or abrasive materials.
Troubleshooting
- Light does not turn ON/OFF:
- Ensure the light bulb is securely screwed into the socket and is within the specified wattage limits.
- Verify that the power to the fixture is ON at the circuit breaker.
- Check the battery in the wireless switch and replace if necessary.
- Re-pair the switch and socket following the 'Pairing Instructions' in the Setup section. Remember to remove the light bulb from the socket before re-pairing.
- Ensure the switch is within the 100-foot range and there are no significant obstructions (e.g., thick walls, metal objects) that could interfere with the RF signal.
- Light turns ON after a power outage:
- The receiver defaults to the ON position when power is restored. This is normal operation.
- Interference:
- While designed to minimize interference, ensure the device is not placed too close to other strong electronic signals if issues occur.
Specifications
| Feature | Specification |
|---|---|
| Model Number | HRLS11B |
| Brand | DEWENWILS |
| Socket Type | E26 / E27 |
| Max Wattage (Incandescent) | 60 watts |
| Max Wattage (LED/CFL) | 20 watts |
| Remote Range | Up to 100 feet (open area) |
| Switch Battery | 1 x 12V (included) |
| Material | Polybutylene Terephthalate (PBT) |
| Mounting Type | Wall Mount (for switch) |
| Package Dimensions | 4.88 x 3.07 x 3.07 inches |
| Weight | 7.05 ounces |


Warranty and Support
For warranty information or technical support, please refer to the product packaging or contact DEWENWILS customer service directly. Contact details can typically be found on the manufacturer's official website or through your purchase platform.