1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your VGEBY Motorcycle Driving Recorder. Please read this manual carefully before using the product to ensure proper function and safety.
The VGEBY Motorcycle Driving Recorder is designed to capture high-quality video footage from both the front and rear of your motorcycle. It features a waterproof design, smart parking monitoring, and a G-sensor for emergency recording, providing reliable documentation of your rides.
2. What's in the Box
- Main Unit (Host)
- Power Cord
- Step-down Line
- USB Cable
- Button Switch Line
- Camera Connection Line
- 2 x Cameras (Front & Rear)
- Mounting Bracket
- 2 x Adhesive Stickers
- 6 x Screws
- Hex Wrench
- User Manual
Figure 1: All components included in the package.
3. Product Overview & Features
The VGEBY Motorcycle Driving Recorder is equipped with advanced features to enhance your riding safety and recording experience:
- Fully Waterproof Design: The DVR host is IP65 waterproof, and the cameras and cables are IP67 waterproof, ensuring reliable operation in various weather conditions.
- Dual AHD Recording: Captures video in 1080p (front) and 720p (rear) resolutions with AHD chip technology for lossless transmission.
- Smart Parking Mode: Automatically initiates recording when the motorcycle detects a collision while parked, providing surveillance.
- G-Sensor: An integrated G-sensor automatically locks video footage during emergencies such as vibrations or collisions, protecting critical evidence.
- 2.0-inch Display: Features a clear 2.0-inch screen for real-time viewing and playback.
- Loop Recording: Supports loop recording in 1, 3, or 5-minute segments, ensuring continuous recording without manual deletion of old files.
- Wired Controller: Allows for manual recording and video locking.
4. Specifications
| Specification | Value |
|---|---|
| Item Type | Motorcycle Driving Recorder |
| Material | ABS |
| Color | Black |
| Display Screen | 2.0 inches |
| Front Camera Angle | 120° |
| Rear Camera Angle | 90° |
| Waterproof Rating (Host) | IP65 |
| Waterproof Rating (Lens & Cable) | IP67 |
| Video Format | AVI |
| Loop Recording | 1 minute, 3 minutes, 5 minutes |
| Frame Rate | 30f/s |
| Memory Card Support | 4GB-32GB (not included) |
| Power Supply | 12-24V to 5V |
| Operating Temperature | -10℃ to 60℃ |
| Battery Type | Built-in high-temperature resistant polymer lithium battery 150mAh |
5. Setup & Installation
Before permanent installation, it is recommended to test all components to ensure they are functioning correctly.
Video 1: General installation reference for a motorcycle dashcam (D6RL model shown, principles apply to VGEBYc392uqgf0d).
5.1. Main Unit Preparation
- Insert Memory Card: Carefully insert a 4GB-32GB memory card (not included) into the card slot on the main unit. Ensure the correct direction to prevent damage.
- Attach Mounting Bracket: Screw the mounting bracket into the host hole on the main unit. Tighten the turnbuckle.
- Apply Adhesive: Attach the double-sided adhesive to the bracket.
Figure 2: Main unit with cables and bracket prepared for installation.
5.2. Power Connection
The power cable needs to be connected to your motorcycle's battery and an ACC (Accessory) power source. It is recommended to test the power module connection before final installation.
Video 2: ACC power cable installation guide (D6RL model shown, principles apply to VGEBYc392uqgf0d).
- Connect to Battery: Connect the black wire of the power cable to the negative terminal of the motorcycle battery and the red wire to the positive terminal.
- Find ACC Power: Use a multimeter to identify a wire that receives 12V power when the motorcycle ignition is on and 0V when off. This is your ACC wire.
- Connect ACC Wire: Open the ACC port on the power cable module, tighten the front end of the yellow wire, and thread it into the port for fixation.
- Test Power Module: Turn on the motorcycle power. The power module's indicator light should illuminate. Turn off the power, and the light should go out. This confirms correct wiring.
- Secure Power Module: Tear off the adhesive tape from the power module and stick it in a suitable position on the motorcycle.
Figure 3: Wiring diagram for power connection.
5.3. Camera Installation
- Prepare Cameras: Install adhesive tape on the back of both camera brackets.
- Mount Front Camera: Install the front camera in a suitable position on the front of the motorcycle, ensuring a clear view. Arrange the cable neatly.
- Mount Rear Camera: Install the rear camera in a suitable position on the rear of the motorcycle, ensuring a clear view. Arrange the cable neatly.
Figure 4: Front camera installation.
Figure 5: Rear camera installation.
5.4. Wired Controller Installation
- Prepare Controller: Stick adhesive tape on the back of the wired controller.
- Mount Controller: Install the wired controller in a suitable and easily accessible position on the motorcycle handlebars.
5.5. Wiring Connections & Management
- Connect Cameras: Connect the front and rear camera cables to the main unit. Pay attention to the labels (e.g.,