Teamson Home 3-Tier Outdoor Water Fountain User Manual

1. Introduction

Thank you for purchasing the Teamson Home 3-Tier Outdoor Water Fountain. This decorative water feature is designed to enhance your outdoor living space with its soothing sounds and illuminated cascading water. Crafted from durable polyresin and stone powder, it features three offset green bowls supported by textured columns, each illuminated by LED lights.

Key features include:

• Decorative 3-tier water fountain suitable for outdoor or indoor use.
• Offset bright green bowls designed to create calming water sounds.
• Textured and offset pedestals forming a contemporary framework.
• Integrated LED lights illuminate the water in each bowl from below.
• Dimensions: 12.2" L x 11.81" W x 28.54" H (31 cm L x 30 cm W x 72.5 cm H).

Image 1.1: The Teamson Home 3-Tier Outdoor Water Fountain, showcasing its design with water flowing and LED lights active.

2. Safety Information

Please read and understand all instructions before operating this product. Failure to follow these instructions may result in electric shock, fire, or serious injury.

• Electrical Safety: Ensure the power outlet is properly grounded and protected by a Ground Fault Circuit Interrupter (GFCI) if used outdoors. Do not operate the fountain with a damaged cord or plug. Keep the power cord away from high traffic areas and sharp edges.
• Water Safety: Always disconnect power before handling the pump or cleaning the fountain. Do not allow children or pets to play with the fountain unsupervised. Use clean water only.
• Placement: Place the fountain on a level, stable surface to prevent tipping. Ensure the fountain is placed where water splashes will not cause damage to surrounding areas or create a slipping hazard.
• Temperature: Do not operate the fountain in freezing temperatures. Drain and store the fountain indoors during winter months to prevent damage.
• Assembly: Do not attempt to modify or disassemble the fountain or its components. Use only original parts supplied by the manufacturer.

3. Package Contents

Carefully unpack all components and inspect for any damage. If any parts are missing or damaged, do not attempt to assemble or operate the fountain. Contact customer support immediately.

• Water Fountain Unit (main body with bowls and pedestals)
• Water Pump with power cord
• LED Lights (pre-installed)
• Instruction Manual

4. Setup Instructions

1. Choose a Location: Select a level, stable surface for your fountain. Ensure it is near a suitable electrical outlet (preferably GFCI protected for outdoor use) and away from areas where water splash could cause damage.
2. Unpack Components: Carefully remove all packaging materials. Place the fountain unit in its desired location.
3. Connect the Pump: Locate the water pump. Connect the pump's tubing to the water outlet tube inside the fountain. Ensure a secure fit. The LED lights are typically pre-installed and connected to the pump or a separate transformer.
4. Fill with Water: Fill the fountain's reservoir with distilled or clean tap water. Ensure the water level is sufficient to completely submerge the pump. Do not overfill.
5. Connect to Power: Plug the power cord into the electrical outlet. The pump and LED lights should activate, and water should begin to flow.
6. Adjust Water Flow (if applicable): Some pumps have an adjustable flow rate. If your pump has this feature, adjust it to achieve your desired water flow.

5. Operating Instructions

• Turning On: Once assembled and filled with water, plug the power cord into a suitable electrical outlet. The fountain will start operating immediately.
• Turning Off: To turn off the fountain, simply unplug the power cord from the electrical outlet.
• Water Level: Regularly check the water level. Due to evaporation and splashing, the water level will decrease over time. Refill as needed to ensure the pump remains fully submerged. Operating the pump without sufficient water can cause damage.
• LED Lights: The LED lights are integrated and will illuminate when the fountain is powered on.

6. Maintenance

Regular maintenance will prolong the life and appearance of your fountain.

• Cleaning the Fountain:
  • Disconnect power before cleaning.
  • Drain the water from the fountain.
  • Use a soft brush or cloth and mild soap with water to clean the surface. Avoid abrasive cleaners that could damage the finish.
  • Rinse thoroughly with clean water.
• Cleaning the Pump:
  • Disconnect power and remove the pump from the fountain.
  • Disassemble the pump cover and impeller.
  • Clean any debris, algae, or mineral buildup from the impeller and pump housing using a small brush and clean water.
  • Reassemble the pump and place it back into the fountain.
• Water Treatment: To prevent algae growth and mineral buildup, consider using a non-toxic fountain algaecide or water clarifier. Follow the product instructions carefully.
• Winterization: In areas with freezing temperatures, drain all water from the fountain and pump. Clean the fountain thoroughly. Store the fountain and pump indoors in a dry, frost-free location during winter to prevent damage from ice expansion.

7. Troubleshooting

8. Specifications

Image 8.1: Product dimensions of the Teamson Home 3-Tier Outdoor Water Fountain.

9. Warranty and Support

Specific warranty information for this product is not available in the provided data. For warranty details, technical support, or replacement parts, please contact Teamson Home customer service directly. Refer to the contact information provided on the product packaging or the official Teamson Home website.

When contacting support, please have your model number (RJ-23074G-EU) and proof of purchase readily available.