1. Introduction
The Shoei Neotec 3 is a state-of-the-art modular motorcycle helmet designed for optimal safety, comfort, and versatility. It features an innovative flip-up design, advanced ventilation, and a robust shell construction to enhance your riding experience. This manual provides essential information for the proper use, care, and maintenance of your Neotec 3 helmet.
Figure 1: Shoei Neotec 3 Modular Motorcycle Helmet, Anthracite Metallic.
2. Initial Setup
Your Shoei Neotec 3 helmet comes with several components to ensure a complete and comfortable riding solution. Before your first ride, please ensure all components are correctly installed and adjusted.
2.1 Included Components
- Helmet
- Breath Guard
- Anti-Fog Sheet (Pinlock)
- Helmet Bag
- Instruction Manual (this document)
2.2 Installing the Anti-Fog Sheet (Pinlock)
The mist-retardant CNS-3C Pinlock shield is crucial for clear vision in various weather conditions. If not pre-installed, carefully follow the instructions provided with the Pinlock insert to attach it to the main visor. Ensure the silicone bead on the Pinlock insert creates a tight seal against the visor to prevent fogging.
Figure 2: Detail of the visor system, showing where the Pinlock insert is installed for anti-fogging.
2.3 Adjusting the Chin Strap
The stainless steel micro ratchet chin strap system provides a secure and precise fit. To fasten, insert the ratchet into the buckle until it clicks securely. To release, pull the red tab to disengage the ratchet. Ensure the strap is snug but comfortable, allowing for proper helmet retention without causing discomfort.
Figure 3: The micro ratchet chin strap for secure fastening.
3. Operation
3.1 Flip-Up Mechanism
The Neotec 3 features a versatile flip-up face cover and face shield, allowing for easy transition between full-face and open-face configurations. To lift the chin bar, locate the release button at the front center of the chin bar and press it firmly while lifting the chin bar upwards until it locks into place. To close, simply pull the chin bar down until it securely latches.
Figure 4: The Neotec 3 in its open-face configuration.
3.2 QSV-2 Sun Shield Visor System
The integrated QSV-2 Sun Shield provides instant relief from sun glare. It can be easily deployed or retracted using the slider located on the left side of the helmet. This system offers clear vision in various lighting conditions without needing to change visors.
Figure 5: Helmet with the internal sun visor extended.
3.3 Ventilation System
The Neotec 3 features multiple venting and extraction points for superior airflow. Adjust the chin vent, top vent, and rear exhaust vents to optimize air circulation and keep you cool and comfortable. These vents are designed for efficient air intake and exhaust, reducing heat buildup inside the helmet.
Figure 6: Top view highlighting the helmet's ventilation system.
3.4 Official Product Video
Watch the official product video for a visual guide on the features and operation of the Shoei Neotec 3 helmet.
Video 1: SHOEI Neotec 3 - Pushing Boundaries. This video showcases the key features and design philosophy behind the Neotec 3 helmet, including its modular functionality, visor system, and aerodynamic properties.
4. Maintenance
Proper maintenance ensures the longevity and safety of your helmet. Always refer to the detailed instructions in the official User Manual (PDF) for comprehensive cleaning and care procedures.
4.1 Cleaning the Exterior
Use a soft cloth dampened with mild soap and water to clean the helmet's exterior. Avoid abrasive cleaners or solvents, as these can damage the finish and shell material. Dry thoroughly with a clean, soft cloth.
4.2 Visor Care
Remove the visor for cleaning. Use only warm water and a soft cloth. For stubborn dirt, a specialized helmet visor cleaner can be used. Do not use harsh chemicals. The Pinlock insert should be cleaned separately with a soft, damp cloth and allowed to air dry.
4.3 Interior Liner Removal and Cleaning
The interior comfort liner and cheek pads are removable for cleaning. Gently detach them from the helmet shell. Hand wash with mild soap and lukewarm water, or machine wash on a gentle cycle in a mesh laundry bag. Air dry completely before re-installing. Ensure all components are dry to prevent mildew and odors.
Figure 7: The interior of the helmet with removable padding for cleaning.
5. Troubleshooting
5.1 Visor Fogging
If your visor fogs up despite the Pinlock insert, ensure the Pinlock is correctly installed and sealed against the main visor. Adjusting the helmet's ventilation by opening the chin and top vents can also help reduce fogging by increasing airflow.
5.2 Excessive Wind Noise
While the Neotec 3 is designed for aerodynamic excellence and reduced wind noise, some noise may occur, especially with vents open. Ensure the visor is fully closed and sealed. Check that the cheek pads are properly seated and provide a snug fit. If noise persists, consider using earplugs for extended rides.
5.3 Chin Bar Not Latching Securely
If the modular chin bar does not latch securely, check for any obstructions in the locking mechanism. Ensure the chin bar is fully lowered and pushed firmly until you hear a distinct click. If the issue persists, inspect the mechanism for damage or wear.
6. Specifications
| Feature | Detail |
|---|---|
| Model Name | Neotec 3 |
| Model Number | 0120-0117-03 |
| Brand | Shoei |
| Shell Material | AIM (Advanced Integrated Matrix) Fiberglass, Expanded Polystyrene (EPS) |
| Safety Standards | DOT FMVSS 218, FMVSS 218 |
| Closure Type | Micro Ratchet Chin Strap |
| Number of Vents | 5 |
| Weight | 4.2 Pounds |
| Style | Modular |
| Color (Current Variant) | Anthracite Metallic |
| Size (Current Variant) | X-Small |
7. Warranty and Support
7.1 Warranty Information
Your SHOEI helmet is covered under warranty for five years from the purchase date, or seven years from the date of manufacture (whichever comes first). The warranty covers all manufacturing defects. Please note that damage caused by the consumer (e.g., dropping the helmet) is not covered under warranty.
