1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your FREEDCONN R1 PLUS E Motorcycle Intercom. Please read this manual thoroughly before using the device to ensure proper function and safety. Retain this manual for future reference.
Image 1: The FREEDCONN R1 PLUS E Motorcycle Intercom unit. This image displays the main unit of the intercom, featuring its sleek black design, control buttons on the top surface, and the 'R1' branding on the side dial. A camera lens is visible on the front left side.
2. Package Contents
Verify that all items are present in your package:
- FREEDCONN R1 PLUS E Intercom Unit
- Headset with Microphones (Boom and Soft Wire)
- Helmet Clamp Mount
- Adhesive Mount
- USB Charging Cable
- User Manual
- Velcro Pads for Speakers and Microphone
3. Product Overview
Familiarize yourself with the main components and controls of the R1 PLUS E intercom unit.
3.1. Unit Components
- Camera Lens: Records video.
- Power/Intercom Button: Controls power and intercom functions.
- Function Button: Manages various features like music playback and call answering.
- Volume Up/Down Buttons: Adjusts audio volume.
- Charging Port: USB-C port for charging and data transfer.
- Headset Port: Connects the headset speakers and microphone.
- Indicator Light: Displays device status (pairing, charging, operation).
Refer to Image 1 for a visual representation of the unit.
4. Setup
4.1. Charging the Device
Before initial use, fully charge the R1 PLUS E unit. Connect the USB charging cable to the charging port on the intercom and to a USB power adapter (not included). The indicator light will show charging status and turn off when fully charged.
4.2. Installing the Intercom on Your Helmet
Choose between the clamp mount or adhesive mount based on your helmet type and preference.
- Clamp Mount:
- Loosen the screws on the clamp mount.
- Slide the clamp between the helmet shell and the inner padding on the left side.
- Tighten the screws to secure the mount.
- Adhesive Mount:
- Clean the desired mounting area on the left side of your helmet.
- Peel off the protective film from the adhesive mount.
- Press the mount firmly onto the helmet surface for at least 30 seconds. Allow 24 hours for the adhesive to cure before use.
- Slide the R1 PLUS E intercom unit onto the installed mount until it clicks into place.
4.3. Installing the Headset
- Attach the speakers to the inside of your helmet using the Velcro pads, positioning them directly over your ears.
- Attach the microphone (boom mic for open-face helmets, soft wire mic for full-face helmets) to the inside of the helmet near your mouth.
- Route the headset wires neatly under the helmet padding to avoid interference.
- Plug the headset connector into the headset port on the R1 PLUS E unit.
5. Operating Instructions
5.1. Power On/Off
- Power On: Press and hold the Power/Intercom Button for approximately 3 seconds until the indicator light flashes.
- Power Off: Press and hold the Power/Intercom Button for approximately 3 seconds until the indicator light turns off.
5.2. Bluetooth Pairing with Mobile Phone
- Ensure the R1 PLUS E is powered off.
- Press and hold the Power/Intercom Button for approximately 5-7 seconds until the indicator light flashes red and blue alternately, indicating pairing mode.
- On your mobile phone, enable Bluetooth and search for "FREEDCONN R1 PLUS E".
- Select the device to pair. A voice prompt will confirm successful pairing.
5.3. Phone Call Functions
- Answer Call: Press the Function Button once.
- End Call: Press the Function Button once during a call.
- Reject Call: Press and hold the Function Button for 2 seconds.
- Redial Last Number: Double-press the Function Button.
5.4. Music Playback
- Play/Pause: Press the Function Button once.
- Next Track: Press the Volume Up button.
- Previous Track: Press the Volume Down button.
5.5. Intercom Communication
The R1 PLUS E supports intercom communication with other compatible FREEDCONN devices.
- Pairing Intercoms:
- Ensure both intercom units are powered off.
- On both units, press and hold the Power/Intercom Button for approximately 5-7 seconds until both indicator lights flash red and blue alternately.
- Briefly press the Power/Intercom Button on one of the units. The units will search and pair with each other. A voice prompt will confirm successful pairing.
- Start Intercom: After pairing, briefly press the Power/Intercom Button on either unit to initiate intercom communication.
- End Intercom: Briefly press the Power/Intercom Button again to end intercom communication.
5.6. Video Recording
The R1 PLUS E features an integrated camera for recording your rides.
- Start Recording: Press the Camera Button (if present, or refer to specific button for camera function). The indicator light will change to confirm recording has started.
- Stop Recording: Press the Camera Button again.
- Note: An SD card (not included) is required for video storage. Ensure it is inserted correctly before recording.
6. Maintenance
- Cleaning: Wipe the unit with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners.
- Storage: Store the device in a cool, dry place when not in use. Avoid extreme temperatures.
- Battery Care: To prolong battery life, charge the device regularly, even if not in frequent use. Avoid fully discharging the battery for extended periods.
- Water Resistance: The R1 PLUS E is designed to be water-resistant, but it is not waterproof. Avoid submerging the device in water.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not power on. | Low battery. | Charge the device fully. |
| Cannot pair with phone. | Device not in pairing mode; Bluetooth off on phone. | Ensure device is in pairing mode (red/blue flashing light). Enable Bluetooth on phone. |
| No audio from speakers. | Headset not connected properly; volume too low. | Check headset connection. Increase volume. |
| Intercom not connecting. | Units not paired; out of range. | Re-pair intercom units. Ensure units are within effective range. |
| Video recording not working. | No SD card; SD card full or corrupted. | Insert a compatible SD card. Format or replace the SD card. |
8. Specifications
- Model: R1 PLUS E
- Bluetooth Version: (Specific version not provided, common for intercoms is 5.0 or higher)
- Intercom Range: (Not provided, typical range varies)
- Battery Type: Rechargeable Lithium-ion
- Charging Time: (Not provided, typically 2-3 hours)
- Operating Time: (Not provided, varies by usage)
- Dimensions: 10 x 5 x 1.3 cm (Approximate, from product data)
- Weight: (Not provided)
- Water Resistance: IPX (Specific rating not provided, generally splash-proof)
Note: Specifications are subject to change without prior notice.
9. Warranty and Support
FREEDCONN products are designed for reliability and performance. For warranty information, technical support, or service inquiries, please refer to the warranty card included with your product or visit the official FREEDCONN website. Keep your proof of purchase for warranty claims.
For further assistance, you may contact FREEDCONN customer support through their official channels.
