1. Introduction
Thank you for purchasing the LEDVANCE Endura Style Stan Table Lamp. This battery-operated outdoor table lamp is designed to provide versatile illumination with adjustable color temperature and dimming functions. This manual provides essential information for the safe and efficient use of your new lamp, including setup, operation, and maintenance instructions.
Figure 1: LEDVANCE Endura Style Stan Table Lamp (Dark Grey)
2. Safety Instructions
Please read these safety instructions carefully before using the product. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- Do not disassemble, repair, or modify the lamp yourself. Contact qualified service personnel for repairs.
- Ensure the charging cable is not damaged before use.
- Keep the lamp away from extreme temperatures, direct sunlight, and open flames.
- This product is rated IP54 for protection against dust and splashing water. Do not immerse the lamp in water.
- Do not cover the lamp during operation or charging to prevent overheating.
- Dispose of batteries according to local regulations. Do not dispose of batteries in fire.
- Keep out of reach of children.
3. Package Contents
Verify that all items listed below are included in your package. If any items are missing or damaged, please contact your retailer.
- 1x LEDVANCE Endura Style Stan Table Lamp
- 1x USB Charging Cable
- 1x Instruction Manual (this document)
Figure 2: Product and included charging cable (within packaging)
4. Setup
4.1 Initial Charging
Before first use, fully charge the lamp's internal battery.
- Locate the USB charging port on the lamp.
- Connect the provided USB charging cable to the lamp's port.
- Connect the other end of the USB cable to a compatible USB power adapter (not included) or a powered USB port.
- The charging indicator light (if present) will show the charging status. Allow approximately [Charging Time, if available, otherwise omit] hours for a full charge.
- Once fully charged, disconnect the charging cable.
4.2 Placement
The LEDVANCE Endura Style Stan Table Lamp is designed for portable outdoor use. Place it on a stable, flat surface. Ensure it is not exposed to extreme weather conditions beyond its IP54 rating (e.g., heavy rain, submersion).
Figure 3: Lamp placed on an outdoor table for ambient lighting
5. Operating Instructions
The lamp is operated via a touch sensor located on the top of the lamp shade.
5.1 Power On/Off
- To turn on: Briefly touch the sensor.
- To turn off: Briefly touch the sensor again.
5.2 Adjusting Brightness (Dimming)
- While the lamp is on, press and hold the touch sensor. The brightness will continuously cycle between 5% and 100%.
- Release the sensor when the desired brightness level is reached.
- The lamp features a brightness memory function, which means it will recall the last set brightness level when turned on again.
5.3 Changing Color Temperature (CCT)
The lamp offers three color temperature settings: 2700 K (Warm White), 4000 K (Neutral White), and 6500 K (Cool White).
- With the lamp on, double-tap the touch sensor to cycle through the available CCT settings.
- The lamp will switch to the next color temperature with each double-tap.
6. Maintenance
6.1 Cleaning
- Ensure the lamp is turned off and disconnected from the charging cable before cleaning.
- Wipe the lamp with a soft, damp cloth. Do not use abrasive cleaners, solvents, or harsh chemicals.
- Do not spray water directly onto the lamp.
6.2 Battery Care
- To prolong battery life, avoid fully discharging the battery frequently.
- If storing the lamp for an extended period, charge it to approximately 50% every 3-6 months.
- Do not expose the battery to high temperatures.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not turn on. | Battery is discharged. | Charge the lamp using the provided USB cable. |
| Lamp does not charge. | Faulty USB cable or power adapter. | Try a different USB cable or power adapter. Ensure connections are secure. |
| Brightness or CCT cannot be adjusted. | Incorrect operation. | Refer to Section 5 for correct operating procedures (press and hold for dimming, double-tap for CCT). |
| Lamp flickers or behaves erratically. | Low battery or internal issue. | Charge the lamp fully. If the problem persists, contact customer support. |
8. Specifications
| Feature | Detail |
|---|---|
| Brand | LEDVANCE |
| Model Number | ENDURA STYLE STAN TABLE CCT USB DG LEDV |
| Dimensions (L x W x H) | 30 x 11 x 30 cm |
| Weight | 520 g |
| Material | Polycarbonate, Aluminum |
| Color | Dark Grey |
| Power Source | Battery Powered (2 Lithium-ion batteries included) |
| Battery Capacity | 4400mAh |
| Voltage | 5 Volts |
| Wattage | 2.5 Watts |
| Luminous Flux | 200 lm |
| Color Temperature (CCT) | 2700 K, 4000 K, 6500 K (selectable) |
| Special Features | Dimmable, Rechargeable, Brightness Memory Function |
| Switch Style | Touch Sensor |
| Protection Rating | IP54 (Dust protected, splash-proof) |
| Minimum Illumination Time | 6.5 hours |
| Country of Origin | China |
9. Warranty Information
LEDVANCE products are manufactured to high quality standards. For specific warranty details, please refer to the warranty card included with your purchase or visit the official LEDVANCE website. Keep your proof of purchase for warranty claims.
10. Customer Support
If you have any questions, require technical assistance, or encounter issues not covered in this manual, please contact LEDVANCE customer support.
- Online Support: Visit the official LEDVANCE website for FAQs and contact information.
- Retailer Support: Contact the retailer from whom you purchased the product.
