Sunrosa 1-6076N

Sunrosa Shower Door 60"x76" Instruction Manual

Model: 1-6076N | Brand: Sunrosa

Introduction

This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your Sunrosa 60"x76" Double Sliding Frameless Shower Door. Please read all instructions carefully before beginning installation to ensure proper setup and long-term performance. Keep this manual for future reference.

Safety Information

  • Always wear safety goggles and gloves during installation.
  • It is recommended that at least two people install this shower door due to the weight and size of the glass panels.
  • Handle glass panels with extreme care. Tempered glass, while strong, can shatter if struck on the edge.
  • Ensure the installation surface (walls, floor) is structurally sound and level before proceeding.
  • Do not use abrasive cleaners or tools on glass or metal surfaces, as this may damage the finish.
  • After installation, allow sealant to cure for at least 24 hours before using the shower.

Package Contents

Verify that all components listed below are present and undamaged before beginning installation. If any parts are missing or damaged, please contact Sunrosa customer support.

  • Tempered Glass Panels (2)
  • Top Rail Assembly
  • Wall Posts (2)
  • Bottom Guide
  • Door Handles (2)
  • Rollers and Mounting Hardware
  • Waterproof Strips / Seal Strips
  • Fasteners and Wall Plugs
  • Installation Hardware Kit

Required Tools

The following tools are required for installation:

  • Measuring Tape
  • Pencil
  • Level
  • Drill (with 6mm and 3.2mm drill bits)
  • Screwdrivers (Phillips and Flathead)
  • Rubber Mallet
  • Utility Knife
  • Caulk Gun and Silicone Sealant
  • Adjustable Wrench / Spanner
  • Hex Key (Allen Wrench)

Installation Guide

Follow these steps carefully for proper installation. Refer to the accompanying video for visual guidance.

Official installation video for Sunrosa Bypass Sliding Glass Shower Doors. This video provides a visual walkthrough of the installation process, complementing the written instructions.

Step 1: Prepare the Opening

Measure the width of your shower opening at the top, middle, and bottom. Ensure the walls are plumb and the floor is level. The adjustable width for this model is 56 1/8" - 60" and height is 76".

Shower door dimensions diagram

Diagram showing the adjustable width and height of the shower door, with measurements.

Step 2: Install Wall Posts

Place the wall posts against the shower walls, ensuring they are plumb using a level. Mark the drill holes through the pre-drilled holes in the wall posts. Drill holes using a 6mm drill bit. Insert wall plugs into the drilled holes. Secure the wall posts to the wall using the provided screws (ST4x35).

Close-up of wall post installation

Detailed view of securing the wall post to the shower wall.

Step 3: Install Bottom Guide and Threshold

Place the threshold along the bottom edge of the shower opening. Position the bottom guide on the threshold and mark its drilling location. Drill holes using a 6mm drill bit and insert wall plugs. Secure the bottom guide with screws (ST3.5x25).

Close-up of bottom guide installation

Image showing the bottom guide and threshold in place.

Step 4: Assemble Top Rail

Attach the top rail to the wall connectors, ensuring it is level. Tighten all screws securely using the provided hex key. Make sure the top rail is perfectly horizontal for smooth door operation.

Close-up of top rail and rollers

View of the top rail assembly with rollers, ensuring level installation.

Step 5: Hang Glass Panels

Carefully lift each glass panel and hang it onto the rollers on the top rail. Ensure the bottom edge of the glass panel fits correctly into the bottom guide. Adjust the rollers if the glass panel appears tilted to ensure smooth sliding.

Installed Sunrosa shower door

The Sunrosa shower door fully installed, showcasing the double sliding design.

Step 6: Install Handles and Seal Strips

Attach the handles to the designated holes on the glass panels. Insert the side door strips along the vertical edges of the glass panels and the bottom strips along the bottom edges. Trim any excess strip material with a utility knife. Apply a bead of silicone sealant along the exterior joints where the wall posts meet the walls and where the threshold meets the floor to ensure a watertight seal.

Close-up of shower door handle

Close-up of the brushed nickel handle on the shower door.

Allow the silicone sealant to cure for at least 24 hours before using the shower to prevent leaks.

Operation

Your Sunrosa shower door features a double sliding design, allowing both panels to slide smoothly. To open or close the door, gently push or pull the handle on either glass panel. Ensure the bottom guide is clear of debris for optimal performance.

Reversible installation diagram

Diagram illustrating the reversible installation and sliding mechanism of the shower door.

Maintenance

Regular cleaning and maintenance will prolong the life and appearance of your shower door.

  • Glass Cleaning: Use a soft cloth or sponge with a mild, non-abrasive glass cleaner. For best results, wipe down the glass after each use to prevent water spots and soap scum buildup.
  • Metal Frame Cleaning: Clean metal components with a soft, damp cloth. Avoid abrasive cleaners, scouring pads, or harsh chemicals, as these can damage the brushed nickel finish.
  • Seal Strips: Periodically check the waterproof strips for wear or damage. Replace them if they show signs of deterioration to maintain a watertight seal.
  • Rollers and Tracks: Keep the top rail and bottom guide tracks clean and free of debris to ensure smooth sliding. You may apply a silicone-based lubricant to the rollers if they become stiff.

Troubleshooting

ProblemPossible CauseSolution
Door does not slide smoothly.Debris in tracks, misaligned rollers, or dry rollers.Clean tracks. Adjust rollers (refer to installation video). Apply silicone lubricant to rollers.
Water leaks from the shower door.Improperly installed seal strips, insufficient sealant, or damaged strips.Ensure seal strips are correctly installed and undamaged. Reapply silicone sealant where necessary, allowing 24 hours to cure.
Glass panel appears tilted.Rollers are not properly adjusted.Adjust the rollers on the top rail until the glass panel is level.

Specifications

  • Brand: Sunrosa
  • Model Number: 1-6076N
  • Color: Brushed Nickel
  • Material: Aluminum, Tempered Glass
  • Style: Bypass Sliding
  • Dimensions: 60"W × 76"H (Adjustable width: 56 1/8" - 60")
  • Glass Thickness: 5/16-inch (8mm)
  • Certifications: ANSI-Certified Tempered Glass
  • Item Weight: 158.7 pounds
  • UPC: 616050970301
Tempered glass detail

Close-up of the 5/16-inch (8mm) ANSI-certified tempered glass, highlighting its clarity and easy-to-clean surface.

Warranty and Support

Sunrosa stands behind the quality of its products. This shower door comes with a commitment to quality. If you are not completely satisfied or receive a defective product, please contact our customer support for prompt resolution.

For assistance, please visit the official Sunrosa Store on Amazon or contact their customer service directly. Refer to your purchase documentation for specific warranty terms and contact details.

Sunrosa Store: Visit Sunrosa Store on Amazon

© 2025 Sunrosa. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.