ALLIANCE LAUNDRY SYSTEMS Control Care Package

1. Introduction

This instruction manual provides essential information for the proper installation, operation, and maintenance of the ALLIANCE LAUNDRY SYSTEMS Control Care Package, model 44063801P. This package is designed as a genuine OEM replacement or upgrade component for various laundry appliances.

The Control Care Package is compatible with Speed Queen, Cissell, Huebsch, IPSO, Unimac, Econo-Wash, Primus, and other Alliance Laundry Systems washer/dryer units. Refer to your appliance's specific service manual for detailed compatibility and installation procedures.

This image displays the ALLIANCE LAUNDRY SYSTEMS Control Care Package, model 44063801P, which is a replacement or upgrade component for compatible laundry appliances.

2. Important Safety Information

Read all instructions carefully before installing or using this product. Failure to follow these instructions may result in property damage, personal injury, or death. Keep this manual for future reference.

• Always disconnect power to the appliance before performing any installation, maintenance, or service.
• Installation should be performed by a qualified technician.
• Wear appropriate personal protective equipment (PPE) during installation and service.
• This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm (Proposition 65 warning).

3. Package Contents

Verify that all components are present and undamaged upon opening the package. If any items are missing or damaged, contact your supplier immediately.

• 1 x ALLIANCE LAUNDRY SYSTEMS Control Care Package (44063801P)

4. Setup and Installation

The Control Care Package is an internal component requiring careful installation. It is strongly recommended that installation be performed by a certified appliance technician to ensure proper function and safety.

1. Preparation: Ensure the appliance is disconnected from its power source. Access the control panel or internal compartment as per your specific appliance's service manual.
2. Removal of Old Component (if applicable): Carefully disconnect and remove the existing control care package or related component, noting all wiring connections and mounting points.
3. Installation of New Component: Connect the new ALLIANCE LAUNDRY SYSTEMS Control Care Package (44063801P) following the wiring diagrams and mounting instructions provided in your appliance's service manual. Ensure all connections are secure and correctly oriented.
4. Reassembly: Reassemble the appliance's panels and secure all fasteners.
5. Testing: Restore power to the appliance and perform a functional test to verify correct operation of the control system.

Refer to the specific service manual for your Speed Queen, Cissell, Huebsch, IPSO, Unimac, Econo-Wash, Primus, or Alliance Laundry Systems washer/dryer for detailed, model-specific installation instructions.

5. Operating Instructions

The Control Care Package is an integral part of your laundry appliance's control system. It does not have direct user-operable controls. Its function is to manage and facilitate the operations of the washer/dryer as designed by the manufacturer.

Once correctly installed, the Control Care Package works automatically in conjunction with the appliance's main control board and user interface. Operate your laundry appliance as you normally would, following the instructions in your appliance's user manual.

6. Maintenance

The ALLIANCE LAUNDRY SYSTEMS Control Care Package (44063801P) is designed for long-term reliability and typically requires no routine user maintenance. However, to ensure the longevity and proper function of your appliance and its components:

• Keep the appliance's environment clean and free from excessive dust or moisture.
• Avoid exposing the appliance to extreme temperatures or humidity.
• If any issues arise, consult a qualified technician for inspection and service. Do not attempt to repair the Control Care Package yourself.

7. Troubleshooting

If your laundry appliance experiences operational issues after the installation of the Control Care Package, consider the following general troubleshooting steps. For specific error codes or symptoms, refer to your appliance's user or service manual.

• No Power: Check if the appliance is properly plugged in and if the circuit breaker has tripped.
• Incorrect Function: Verify that all wiring connections to the Control Care Package were made correctly during installation.
• Error Codes: Consult your appliance's manual for the meaning of any displayed error codes and recommended solutions.
• Intermittent Operation: Ensure there are no loose connections or signs of damage to the component or its wiring.

If troubleshooting steps do not resolve the issue, contact a qualified service technician for assistance.

8. Specifications

9. Warranty and Support

For warranty information regarding the ALLIANCE LAUNDRY SYSTEMS Control Care Package (44063801P), please refer to the documentation provided with your purchase or contact the seller or Alliance Laundry Systems directly. Warranty terms may vary based on the point of purchase and region.

For technical support or service inquiries, please contact your authorized Alliance Laundry Systems dealer or a qualified appliance service technician. When contacting support, please have your appliance model number, serial number, and the part number (44063801P) readily available.