1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Brondell T44-RW Swash Thinline Electric Bidet Toilet Seat. Please read this manual thoroughly before installation and use to ensure proper function and safety. Keep this manual for future reference.
Figure 1: Brondell T44-RW Swash Thinline Electric Bidet Toilet Seat.
2. Safety Information
Observe all safety precautions to prevent injury or damage. This appliance is for household use only. Do not immerse the unit in water. Ensure the electrical outlet is a Ground Fault Circuit Interrupter (GFCI) type and is properly grounded. Disconnect power before cleaning or servicing.
Electrical Safety
- Use only with a 120V AC, 60Hz, 15A grounded outlet.
- Do not operate if the power cord or plug is damaged.
- Keep the power cord away from heated surfaces.
Water Supply Safety
- Connect to a cold water supply only.
- Ensure all connections are tight to prevent leaks.
- Do not use excessive force when tightening connections.
3. Package Contents
Verify that all components are present before beginning installation:
- Brondell T44-RW Bidet Toilet Seat
- Wireless Remote Control with Wall Mount
- Mounting Plate and Bolts
- T-Valve Connector
- Bidet Hose
- Installation Parts (washers, nuts, etc.)
- User Manual
4. Installation
Follow these steps for proper installation. No specialized tools are required, and a plumber is generally not needed.
4.1 Determine Toilet Fit
Before installation, ensure your toilet is compatible with the round T44-RW model. Measure your toilet bowl as shown in Figure 2.
Figure 2: Toilet Measurement Guide.
- Measure A (Bolt holes to front of bowl): For a round bidet seat, this distance should be 16"-17.75".
- Measure B (Bolt holes to toilet tank): This distance must be at least 1.5".
- Measure C (Distance between bolt holes): This distance should be 5.25"-7.45".
The T44-RW is designed for round toilets. For elongated toilets, a different model (T44-EW) is required.
Figure 3: Round vs. Elongated Toilet Bowl Comparison.
4.2 Preparation
- Turn off the water supply valve to your toilet.
- Flush the toilet to drain the tank.
- Disconnect the existing water supply hose from the toilet tank.
- Remove your existing toilet seat and lid.
4.3 Installing the T-Valve
- Install the T-valve onto the fill valve under your toilet tank. Ensure the rubber washer is correctly seated.
- Connect the toilet's original water supply hose to the bottom of the T-valve.
- Connect the bidet hose (included) from the T-valve to the water inlet on the side of the bidet seat. Hand-tighten all connections, then use a wrench for a final quarter-turn to ensure no leaks. Do not overtighten.
4.4 Mounting the Bidet Seat
- Place the mounting plate over the toilet bolt holes.
- Insert the mounting bolts through the plate and toilet holes. Secure with conical washers and nuts from underneath the toilet.
- Slide the bidet seat onto the mounting plate until it clicks into place. Adjust the seat position as needed for a secure and comfortable fit.
Figure 4: Installed Brondell T44-RW Bidet Seat.
4.5 Electrical Connection
- Plug the bidet seat's power cord into a grounded GFCI electrical outlet. The power cord is 47.2 inches long.
4.6 Final Steps
- Slowly turn on the water supply valve to the toilet. Check for any leaks.
- Allow the bidet's water tank to fill (this may take a few minutes).
- Perform a test wash cycle to ensure proper function.
5. Operating Instructions
The Brondell T44-RW is operated using the included wireless remote control. The remote features user-favorite presets and an ergonomic design.
Figure 5: Wireless Remote Control.
5.1 Basic Wash Functions
- Rear Wash: Press the "Rear" button for a standard posterior wash.
- Front Wash: Press the "Front" button for a feminine wash.
- Strong Wash: Press the "Strong" button for a more powerful wash.
- Oscillation: During a wash cycle, press the oscillation button to move the nozzle back and forth for a wider cleaning area.
5.2 Adjusting Settings
- Water Temperature: Use the "Water Temp." button to cycle through available water temperature settings (e.g., Low, Medium, High, Off).
- Water Pressure: Use the "+" and "-" buttons (often near "Water Pressure") to adjust the water spray intensity.
- Nozzle Position: Use the "Nozzle Position" arrows to adjust the nozzle's forward or backward position.
- Seat Temperature: Use the "Seat Temp." button to adjust the heated seat temperature.
- Warm Air Dryer: After a wash, press the "Dry" button to activate the warm air dryer. Use the "+" and "-" buttons to adjust the air temperature or intensity.
5.3 Additional Features
- Night Light: The 7-color LED night light can be activated or deactivated via the remote. It provides illumination for nighttime use.
- Deodorizer: The activated carbon deodorizer automatically engages to neutralize odors.
- User Presets: The remote allows for programming and saving two individual user settings for personalized comfort. Refer to the remote control section of the full manual for detailed programming instructions.
Figure 6: Bidet Seat Night Light Feature.
6. Maintenance
Regular cleaning and maintenance ensure optimal performance and hygiene of your bidet seat.
6.1 Cleaning the Nozzle
The stainless steel nozzle performs an automatic self-cleaning rinse before and after each use. For manual cleaning:
- Press the "Nozzle Cleaning" button on the remote to extend the nozzle.
- Gently clean the nozzle with a soft brush or cloth and mild soap. Do not use harsh chemicals or abrasive cleaners.
- Press "Stop" or wait for the nozzle to retract automatically.
Figure 7: Stainless Steel Nozzle.
6.2 Cleaning the Bidet Seat
- Unplug the power cord from the electrical outlet.
- Wipe the exterior surfaces of the bidet seat with a soft, damp cloth and a mild, non-abrasive cleaner.
- Do not spray water directly onto the unit.
- Ensure the unit is completely dry before plugging it back in.
6.3 Winterization (If Applicable)
If the bidet seat will be exposed to freezing temperatures, it must be drained to prevent damage. Refer to the full product manual for detailed winterization instructions.
7. Troubleshooting
If you encounter issues, consult the following table before contacting customer support.
| Problem | Possible Cause | Solution |
|---|---|---|
| No water spray | Water supply valve closed; bidet hose kinked; water filter clogged (if installed). | Open water supply valve; straighten hose; check/replace water filter. |
| No power | Power cord unplugged; GFCI tripped; power outage. | Ensure plug is secure; reset GFCI; check household power. |
| Water temperature not changing | Temperature setting incorrect; water heater issue. | Adjust water temperature setting on remote; allow time for water to heat. |
| Remote control not responding | Batteries low or dead; remote out of range; obstruction. | Replace remote batteries; ensure clear line of sight to bidet; move closer. |
| Leaks from connections | Loose connections; damaged washers. | Tighten connections (do not overtighten); replace washers if damaged. |
8. Specifications
| Feature | Detail |
|---|---|
| Model | T44-RW |
| Type | Electric Bidet Toilet Seat |
| Shape | Round |
| Dimensions (L x W x H) | 20.7" L x 15" W x 3.9" H (99mm height) |
| Weight | 8.7 Pounds |
| Material | Plastic |
| Nozzle Material | Stainless Steel |
| Water Heating | Instant Ceramic Water Heater (Endless Warm Water) |
| Heated Seat | 3-Temperature Settings |
| Warm Air Dryer | 5-Level Settings |
| Deodorizer | Activated Carbon |
| Night Light | 7-Color LED |
| Power Cord Length | 47.2 inches |
| Power Supply | 120V AC, 60Hz |
| UPC | 819911010479 |
9. Warranty and Support
Brondell products are designed for quality and durability. For specific warranty details, please refer to the warranty card included with your product or visit the official Brondell website. For technical assistance or customer service, please contact Brondell support directly.
You can find more information and support resources on the Brondell Store on Amazon.
