1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your JOROBURO S866 Electric Bike LCD Display. Designed for electric bicycles and scooters, this display offers essential riding data and control functions. Please read this manual thoroughly before use to ensure proper function and safety.
2. Safety Information
- Ensure the display is securely mounted and all connections are waterproof before riding.
- Do not attempt to disassemble or modify the display.
- Always prioritize road safety. Do not operate the display while riding if it distracts you.
- Verify compatibility with your e-bike's controller (UART No. 2 protocol, 5-pin plug) before installation to prevent damage.
3. Package Contents
- 1 x JOROBURO S866 LCD Display
- 1 x Instruction Manual (this document)
4. Product Overview
The S866 LCD display features a clear screen and intuitive buttons for easy control and monitoring of your e-bike's performance.
Figure 4.1: Front view of the JOROBURO S866 LCD Display, showing the screen and control buttons.
4.1 Display Components
- LCD Screen: Displays speed, battery level, assist level, trip distance, and other data.
- '+' Button: Increases assist level, navigates menu up.
- 'Power' Button: Turns display on/off, confirms selections, enters menu.
- '-' Button: Decreases assist level, navigates menu down.
- 5-Pin Waterproof Connector: For connection to the e-bike controller.
Figure 4.2: Close-up view of the display's control buttons: Plus (+), Power, and Minus (-).
5. Installation
- Mounting: Attach the display bracket to your e-bike's handlebars (suitable for 22.5mm handlebars). Secure it firmly using the provided screw.
- Connection: Locate the 5-pin UART No. 2 protocol connector on your e-bike's controller. Align the pins and firmly connect the display's waterproof connector. Ensure a secure fit to prevent water ingress.
- Cable Management: Route the cable safely, ensuring it does not interfere with steering or moving parts. Use cable ties if necessary.
Figure 5.1: Dimensions of the S866 LCD Display and its integrated mounting bracket.
Figure 5.2: The 5-pin waterproof connector of the S866 LCD Display.
6. Operating Instructions
6.1 Power On/Off
- To turn on the display, press and hold the 'Power' button for approximately 2 seconds.
- To turn off the display, press and hold the 'Power' button for approximately 2 seconds.
6.2 Adjusting Assist Level
- Press the '+' button to increase the pedal assist level.
- Press the '-' button to decrease the pedal assist level.
- The current assist level will be displayed on the screen.
6.3 Displayed Information
The S866 display provides the following information:
- Speed: Current riding speed (km/h or mph).
- Assist Level: Current pedal assist level (e.g., 0-5).
- Battery Level: Graphical representation of remaining battery charge.
- Trip Distance: Distance covered during the current ride.
- Odometer: Total distance covered by the e-bike.
Figure 6.1: The S866 display showing various riding parameters.
6.4 Accessing Settings (P-Settings)
To access advanced settings (P-settings), typically press and hold the '+' and '-' buttons simultaneously for a few seconds while the display is on. Navigation within the menu is usually done with '+' and '-' buttons, and selection/confirmation with the 'Power' button. Common settings include:
- P01: Backlight brightness (1-3 levels).
- P02: Mileage unit (0: km, 1: mile).
- P03: Voltage level (24V, 36V, 48V). Important: Set this correctly to match your e-bike's battery voltage.
- P04: Sleep mode time (0: never, 1-60 minutes).
- P05: Assist gear (0: 3 gears, 1: 5 gears).
- P06: Wheel diameter (inches).
- P07: Speed magnet number.
- P08: Speed limit.
- P09: Zero start/Non-zero start (0: zero start, 1: non-zero start).
- P10: Drive mode (0: pedal assist only, 1: electric only, 2: both).
- P11: Assist sensitivity.
- P12: Assist start strength.
- P13: Magnet disk type (5, 8, 12).
- P14: Controller current limit.
- P15: Undervoltage value.
- P16: ODO reset.
- P17: Cruise control (0: off, 1: on).
- P18: Password setting (if applicable).
Note: The exact P-settings and their functions may vary slightly. Refer to your e-bike's controller manual for specific details if available. Incorrect settings can affect performance or damage components.
7. Maintenance
- Cleaning: Wipe the display screen and body with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Water Exposure: While the connector is waterproof, avoid submerging the display. If it gets wet, dry it thoroughly before use.
- Storage: Store the e-bike and display in a dry, cool place when not in use.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Display does not power on. | Loose connection, no power from controller, damaged display. | Check all connections. Ensure e-bike battery is charged and turned on. Verify controller is functioning. |
| Display shows incorrect speed/distance. | Incorrect wheel diameter or magnet number setting (P06, P07). | Access P-settings and adjust P06 (wheel diameter) and P07 (speed magnet number) to match your e-bike's specifications. |
| Display shows error code or unexpected behavior. | Incompatible controller, incorrect voltage setting (P03), internal fault. | Verify your e-bike controller uses UART No. 2 protocol. Check P03 setting matches your battery voltage (24V, 36V, 48V). If issues persist, consult a professional. |
| Display requires a password. | Password protection enabled (P18). | If you set a password and forgot it, try common defaults like 0000, 1234, 3745, or 6666. If unsuccessful, you may need to contact the manufacturer or a service center for assistance. |
| Display is dim or hard to read. | Low backlight setting (P01). | Adjust P01 in settings to increase backlight brightness. |
9. Specifications
- Model: S866
- Brand: JOROBURO
- Material: ABS
- Voltage Compatibility: 24V, 36V, 48V (auto-detect or configurable via P-settings)
- Connector Type: 5-Pin Waterproof Connector
- Protocol: UART No. 2
- Display Type: LCD with Backlight
- Dimensions (Display Unit): Approximately 8cm (3.1in) x 4.8cm (1.9in) x 4.8cm (1.9in)
- Cable Length: Approximately 21cm (8.3in)
- Weight: 3.52 ounces (approx. 100g)
- Handlebar Clamp Diameter: Designed for 22.5mm handlebars
Figure 9.1: Detailed dimensions of the S866 LCD Display.
10. Warranty and Support
This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For warranty claims, technical support, or further assistance, please contact your retailer or the JOROBURO customer service department. Keep your purchase receipt as proof of purchase.
For general inquiries or to learn more about JOROBURO products, please visit the official brand website or contact customer support through your purchase platform.