Introduction
This manual provides instructions for the safe installation, operation, and maintenance of your Maxxima 2-inch Ultra-Thin Recessed Anti-Glare LED Downlight, Model MRL-S20803SBW. This fixture is designed for residential and commercial indoor applications, offering adjustable color temperature and dimming capabilities. Please read these instructions thoroughly before installation and retain them for future reference.
Safety Information
WARNING: RISK OF ELECTRIC SHOCK. DISCONNECT POWER AT THE CIRCUIT BREAKER BEFORE INSTALLATION OR SERVICING.
- All electrical connections must be in accordance with local and National Electrical Code (NEC) standards. Consult a qualified electrician if you are unfamiliar with proper electrical wiring connections.
- This fixture is intended for installation in ceilings only.
- Do not modify the fixture or use it for purposes other than its intended use.
- Ensure the supply voltage is 120VAC.
- This product is IC Rated, suitable for direct contact with insulation.
- This fixture is Damp Rated, suitable for use in bathrooms and kitchens where moisture may be present.
Package Contents
Verify that all components are present before beginning installation:
- 1 x Maxxima 2-inch Square LED Downlight Fixture (White Trim, Black Baffle)
- 1 x Remote Junction Box with Integrated CCT Selectable Switch
- 1 x Foam Gasket (pre-attached or included)
This image displays the complete Maxxima 2-inch square LED downlight unit, including the main fixture with its white trim and deep-set black baffle, and the connected external junction box.
Setup and Installation
Follow these steps for proper installation:
Tools Required:
- Wire Strippers
- Screwdriver (Phillips and Flathead)
- Hole Saw or Template (2.5-inch diameter)
- Measuring Tape
Installation Steps:
- Turn Off Power: Locate the circuit breaker controlling the area where the downlight will be installed and turn off the power. Verify power is off using a voltage tester.
- Prepare Ceiling Opening: Using a 2.5-inch hole saw or template, cut a circular opening in the ceiling at the desired location. Ensure there are no obstructions (e.g., joists, pipes) behind the cutting area.
- Access Junction Box: Open the cover of the remote junction box.
- Wire Connections: Connect the household electrical wires to the junction box wires. Use appropriate wire connectors (not included) to secure the connections:
- Connect the black (Live) wire from the supply to the black wire of the junction box.
- Connect the white (Neutral) wire from the supply to the white wire of the junction box.
- Connect the green or bare copper (Ground) wire from the supply to the green wire of the junction box.
This image displays the interior of the junction box with its cover open, revealing the wiring terminals for electrical connections (black, white, green) and the prominent 5 CCT selector switch.
- Select Color Temperature (CCT): Before closing the junction box, use the switch located on the side of the junction box to select your desired color temperature (2700K, 3000K, 3500K, 4000K, or 5000K).
A magnified view of the 5 CCT switch on the side of the junction box, clearly showing the selectable color temperature options: 2700K, 3000K, 3500K, 4000K, and 5000K.
This image illustrates the key feature of 5 CCT (Correlated Color Temperature) selection. It shows the downlight fixture alongside a magnified view of the switch located on the junction box, indicating options for 2700K (Soft White), 3000K (Warm White), 3500K (Bright White), 4000K (Neutral White), and 5000K (Daylight).
- Secure Junction Box: Close the junction box cover and secure it. Place the junction box into the ceiling cavity, ensuring it is not pinched or stressed.
- Connect Fixture to Junction Box: Connect the male connector from the downlight fixture to the female connector on the junction box's installation cord. Ensure a secure connection.
- Insert Downlight Fixture: Gently push the spring-loaded clips on the sides of the downlight fixture upwards and insert the fixture into the ceiling opening. Release the clips to secure the fixture flush against the ceiling. The foam gasket will help create a tight seal.
The back view of the Maxxima 2-inch square LED downlight, revealing the heat sink fins for thermal management and the spring-loaded clips used for securing the fixture in the ceiling.
- Restore Power: Once the fixture is securely installed, restore power at the circuit breaker.
A lifestyle image demonstrating several Maxxima 2-inch square LED downlights seamlessly integrated into the ceiling of a contemporary kitchen and living space, providing ambient lighting.
Operating Instructions
Your Maxxima LED Downlight is designed for simple operation:
- Power On/Off: The downlight is controlled by a standard wall switch connected to the electrical circuit.
- Dimming: This fixture is compatible with most standard LED dimmers, allowing for a dimmable range of 20% to 100%. Ensure your dimmer is compatible with LED lighting for optimal performance.
- Color Temperature Selection: The color temperature (CCT) is set using the switch on the junction box during installation. It cannot be changed without accessing the junction box.
A detailed close-up of the Maxxima 2-inch square LED downlight after installation, showing the white trim flush with the ceiling and the black baffle housing the illuminated LED.
Maintenance
The Maxxima LED Downlight requires minimal maintenance:
- Cleaning: To clean the fixture, ensure power is off. Wipe the surface with a soft, dry, or slightly damp cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish or electrical components.
- No User-Serviceable Parts: The LED light source is integrated and not replaceable. Do not attempt to open or repair the fixture.
Troubleshooting
If you encounter issues with your downlight, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power to the fixture. Loose wiring connection. Incorrect CCT switch setting. | Check circuit breaker and wall switch. Verify all wire connections in the junction box are secure (ensure power is off first). Confirm CCT switch on junction box is set to a valid position. |
| Light flickers or dims inconsistently. | Incompatible dimmer switch. Loose wiring connection. | Ensure you are using an LED-compatible dimmer switch. Check all wiring connections (with power off). |
| Incorrect color temperature. | CCT switch set incorrectly. | Access the junction box (power off) and adjust the CCT selection switch to the desired setting. |
Specifications
| Feature | Specification |
|---|---|
| Brand | Maxxima |
| Model Number | MRL-S20803SBW |
| Power Consumption | 9 Watts |
| Brightness | 500 Lumens |
| Input Voltage | 120VAC |
| Color Temperature (CCT) | 2700K / 3000K / 3500K / 4000K / 5000K Selectable |
| Color Rendering Index (CRI) | 90 |
| Dimming Range | 20% - 100% (with compatible LED dimmer) |
| Fixture Dimensions (L x W x H) | 3.16" x 3.16" x 2.6" |
| Junction Box Dimensions (H x W x D) | 1.25" x 3.4" x 3.4" |
| Recommended Hole Cutout | 2.5 inches |
| Material | Aluminum |
| Finish | White Trim, Black Baffle |
| Certifications | ETL Listed, IC Rated |
| Environment Rating | Damp Rated (Indoor Use) |
| Beam Spread | 36° |
| Item Weight | 10.72 ounces |
A technical diagram illustrating the physical dimensions of the Maxxima 2-inch square LED downlight, with measurements of 3.16 inches in length, 3.16 inches in width, and 2.6 inches in height.
Warranty and Support
This Maxxima LED Downlight is backed by a 3-year warranty from the date of purchase, covering defects in materials and workmanship under normal use.
For technical assistance, warranty claims, or product inquiries, please contact Maxxima customer service. Refer to the product packaging or the official Maxxima website for current contact information.
