Rev-A-Shelf 5WU2-3N1-1

Rev-A-Shelf 3" Pullout Organizer (Model 5WU2-3N1-1) Instruction Manual

1. Product Overview

This Rev-A-Shelf 2-tier narrow upright pullout organizer is designed to maximize storage space within your cabinets. It features a solid bottom and a protective soft-close mechanism. The unit is equipped with a 3-piece zinc-plated 7/8 extension ball-bearing slide system for smooth operation. Its durable construction includes natural compact melamine shelves with chrome round wire accents.

Rev-A-Shelf 3-inch pullout organizer installed in a cabinet, showcasing its two tiers and narrow design.
The Rev-A-Shelf 3-inch pullout organizer shown installed in a kitchen cabinet, providing organized storage for various items.

2. Setup and Installation

2.1 Before You Begin

Ensure your cabinet meets the minimum opening requirements for proper installation:

  • Face Frame Cabinet: Minimum 6.00"W x 10.75"D x 12.00"H
  • Frameless Cabinet: Minimum 6.00"W x 10.75"D x 12.00"H

This organizer is designed for 9" and larger wall cabinets with minimum depths of 10-3/4".

Diagram illustrating how to measure cabinet openings for width, depth, and height for both framed and frameless cabinets.
Refer to this diagram for accurate measurement of your cabinet space to ensure proper fit.

2.2 Tools Required

The following tools are typically needed for installation:

  • Power Drill
  • Pencil
  • Screwdriver
  • Tape Measure

2.3 Installation Steps

The unit comes with a mounting base, the two-tier pullout, ball-bearing slides, and all necessary mounting hardware. Detailed assembly instructions are included with the product packaging. Please follow them carefully.

  1. Unpack Components: Carefully remove all parts from the packaging and verify against the included parts list.
  2. Position Mounting Base: Place the mounting base inside your cabinet, ensuring it is flush with the cabinet floor and properly aligned.
  3. Secure Mounting Base: Use the provided screws and a power drill/screwdriver to securely fasten the mounting base to the cabinet floor.
  4. Attach Pullout Unit: Slide the two-tier pullout unit onto the ball-bearing slides on the secured mounting base until it clicks into place.
  5. Test Operation: Gently pull the organizer out and push it back in to ensure smooth operation and proper soft-close functionality.
Top view of the pullout organizer's base, showing the mounting points and slide mechanism.
The mounting base with ball-bearing slides, ready for installation into the cabinet.

3. Operating Instructions

To operate the Rev-A-Shelf pullout organizer, simply grasp the front of the unit and pull it outwards. The full-extension ball-bearing slides allow the entire unit to extend from the cabinet, providing complete access to items stored on both tiers. To close, gently push the unit back into the cabinet; the soft-close feature will engage to ensure a quiet and smooth return.

The two-tier pullout organizer filled with various kitchen jars and bottles, extended from the cabinet.
The pullout organizer fully extended, demonstrating easy access to stored items on both tiers.

4. Maintenance

To maintain the appearance and functionality of your pullout organizer, follow these simple guidelines:

  • Cleaning: Wipe the shelves and chrome accents with a dry cloth. Avoid abrasive cleaners or harsh chemicals that could damage the finish.
  • Slide Lubrication: Periodically check the ball-bearing slides for smooth operation. If needed, a light application of silicone-based lubricant can be applied to the slides.
  • Fastener Check: Occasionally inspect all mounting screws and fasteners to ensure they remain tight. Tighten if necessary to maintain stability.

5. Troubleshooting

If you encounter any issues with your Rev-A-Shelf pullout organizer, consider the following:

  • Unit Not Sliding Smoothly: Check for any obstructions in the cabinet or along the slide mechanism. Ensure the slides are clean and free of debris. A light lubricant may be applied if dryness is the issue.
  • Unit Feels Loose or Wobbly: Verify that all mounting screws are securely tightened to the cabinet floor. Ensure the pullout unit is correctly seated on the slide mechanism.
  • Soft-Close Not Engaging: Confirm that the unit is fully pushed back into the cabinet. Check for any obstructions preventing the soft-close mechanism from fully engaging.
  • Overloading: Ensure the organizer is not overloaded beyond its recommended weight capacity, as this can affect slide performance and stability.

If problems persist, refer to the detailed assembly instructions provided with your product or contact Rev-A-Shelf customer support.

6. Product Specifications

Detailed specifications for the Rev-A-Shelf 3" Pullout Organizer (Model 5WU2-3N1-1):

FeatureDetail
Model Number5WU2-3N1-1
MaterialAlloy Steel, Melamine
Finish TypePolished (Chrome Accents)
ColorLight Brown (Shelves)
Product Dimensions (D x W x H)10.6"D x 3.03"W x 10.5"H
Number of Shelves2
Mounting TypeCabinet Floor Mounted
Extension TypeFull-extension, 3-Piece Zinc Plated 7/8 Ball-Bearing Slide System
Special FeatureSoft-Close, Modular Design
Weight CapacityMinimum 5.7 Pounds (Specific maximum not provided, avoid overloading)
Required AssemblyYes
Product CareWipe with Dry Cloth
Detailed diagram showing the dimensions of the two-tier upright storage pullout, including width, depth, height, and clearance between shelves.
Dimensional drawing of the pullout organizer, highlighting key measurements.

7. Safety Information

Always adhere to the assembly instructions for safe installation. Ensure the shelf is properly mounted to the cabinet floor to prevent accidents. Do not overload the shelf beyond its weight capacity to maintain stability and prevent damage to the unit or cabinet.

8. Warranty and Support

For specific warranty details and customer support, please refer to the documentation included with your purchase or visit the official Rev-A-Shelf website. You can also find more information and contact options on the Rev-A-Shelf Brand Store on Amazon.