1. Introduction
Welcome to the user manual for your Amerec AI Series Comfort-Flo 3/4" Steam Head with Insulator. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your steam head. Please read these instructions thoroughly before installation and use to ensure a safe and pleasurable steam bath experience.
2. Product Overview
Key Features
- Integral reservoir for a scented steam bath (aromatherapy).
- 3/4 Inch NPT Connection for standard plumbing.
- 180 Degree steam dispersion pattern for even heat distribution.
- Safe operation with an internal Ryton plastic insulator, preventing the exterior metal surface from reaching high temperatures.
- Reduces the time required to reach the desired room temperature.
Package Contents
- ComfortFlo steam head
- Insulator
- Installation and Operation manual (this document)
Product Image
This image displays the Amerec AI Series Comfort-Flo 3/4 inch Steam Head with its insulator. The steam head is designed for efficient steam dispersion and includes a reservoir for aromatherapy.
3. Safety Information
Important Safety Instructions
- Read all instructions thoroughly before installation and use.
- Ensure proper grounding of the steam generator system.
- Do not block the steam outlet during operation.
- Keep children and pets away from the steam head and steam plume.
- Steam is extremely hot; avoid direct contact with the steam plume to prevent burns.
- Installation should be performed by a qualified electrician and plumber in accordance with local codes and regulations.
- Never operate the steam head if it appears damaged or is not functioning correctly.
4. Setup (Installation)
Installation Requirements
- A dedicated 3/4 Inch NPT connection point for the steam head.
- Ensure adequate clearance around the steam head for proper steam dispersion and maintenance.
- Install in a location that allows for safe steam dispersion, away from direct contact with bathers.
Installation Steps
- Identify the steam outlet pipe in your steam room where the steam head will be installed.
- Apply an appropriate thread sealant (e.g., PTFE tape or pipe dope) to the 3/4 inch NPT male threads on the steam head.
- Carefully thread the steam head onto the steam outlet pipe, ensuring a secure and watertight connection. Do not overtighten.
- Position the steam head to allow for 180-degree steam dispersion without obstruction.
- Verify all connections are tight and leak-free before operating the steam generator.
5. Operating Instructions
Basic Operation
- Ensure the steam generator is properly connected, filled with water, and powered on (refer to your specific steam generator manual for details).
- Turn on the steam generator according to its operating instructions.
- After a short warm-up period, steam will begin to emit from the Comfort-Flo steam head.
- Adjust steam duration and temperature via your steam generator's control panel as desired.
Using the Fragrance Reservoir
- Locate the integral fragrance reservoir on the top of the steam head.
- Carefully add a few drops of your preferred aromatherapy fragrance oil into the reservoir. Do not overfill.
- The heat from the steam will naturally diffuse the fragrance into the steam room, enhancing your steam bath experience.
- Clean the reservoir regularly to prevent residue buildup.
6. Maintenance
Cleaning the Steam Head
Regularly inspect the steam head for mineral buildup or blockages to ensure optimal performance.
- Ensure the steam generator is turned off and has completely cooled down before attempting any cleaning.
- Wipe the exterior of the steam head with a soft, damp cloth.
- For stubborn mineral deposits, use a mild descaling solution specifically designed for steam equipment, applying it carefully to avoid contact with the steam outlet. Follow the descaling solution manufacturer's instructions.
- Rinse thoroughly with clean water after cleaning.
Insulator Care
The internal Ryton plastic insulator is crucial for preventing the exterior of the steam head from reaching high temperatures. Do not attempt to remove or modify the insulator. If you suspect damage to the insulator or if the exterior of the steam head becomes excessively hot during operation, discontinue use immediately and contact Amerec customer support.
7. Troubleshooting
Common Issues and Solutions
| Problem | Possible Cause | Solution |
|---|---|---|
| No steam from head | Steam generator is off, faulty, or out of water. | Check steam generator power, water supply, and error codes. Refer to generator manual. |
| Low steam output | Steam head blocked by mineral buildup or generator issue. | Clean steam head as per maintenance section. Consult generator manual for low output issues. |
| Exterior of steam head too hot | Insulator damage or improper installation. | Discontinue use immediately. Contact Amerec customer support for inspection. |
| No fragrance diffusion | Fragrance reservoir is empty or blocked. | Refill reservoir with fragrance oil. Ensure no blockages in the reservoir or diffusion path. |
For issues not listed above, or if troubleshooting steps do not resolve the problem, please contact Amerec customer support for further assistance.
8. Specifications
Product Specifications
- Model: 8816-38
- Material: Stainless Steel (exterior), Ryton plastic (insulator)
- Connection: 3/4 Inch NPT
- Steam Dispersion: 180 Degrees
- Dimensions (Steam Head): Width: 3 Inch, Depth: 1 1/2 Inch, Height: 2 1/8 Inch
- Product Dimensions (Overall): 1.5 x 3 x 2.18 inches
- Weight: 3 lbs
- Color: Brushed Bronze
- Included Components: Steam head and insulator
9. Warranty & Support
Warranty Information
Amerec products are manufactured to high-quality standards. For specific warranty details pertaining to your Comfort-Flo Steam Head, please refer to the warranty card included with your steam generator or visit the official Amerec website. It is important to retain your proof of purchase for any warranty claims.
Customer Support
For technical assistance, replacement parts, or warranty inquiries, please contact Amerec customer support. Our team is available to help you with any questions or concerns.
Website: www.amerec.com
Phone: Please refer to Amerec's official website for current contact numbers and hours of operation.
