Introduction
Thank you for choosing the Adamson B10 Single Bed Cooling System. This innovative system is designed to provide a comfortable and cool sleeping environment, effectively reducing night sweats and discomfort for hot sleepers. The B10 utilizes a water-based cooling method, circulating cold water through a 100% cotton mattress pad to maintain an optimal temperature for restful sleep.
The Adamson B10 is an energy-efficient solution, consuming significantly less power than traditional air conditioning units, contributing to both cost savings and environmental preservation. Please read this manual thoroughly before installation and operation to ensure safe and optimal performance of your device.
Safety Information
- Always ensure the cooling unit is placed on a stable, level surface.
- Do not immerse the cooling unit in water or other liquids.
- Keep the unit away from direct sunlight and heat sources.
- Use only clean, distilled water in the reservoir to prevent mineral buildup and ensure longevity.
- Ensure all hose connections are secure to prevent leaks.
- Unplug the unit from the power outlet before cleaning or maintenance.
- Keep out of reach of children and pets.
- Do not attempt to repair or modify the unit yourself. Contact customer support for assistance.
Package Contents
Please verify that all components are present in your package:
- Adamson B10 Cooling Unit
- Single Bed Mattress Pad (100% Cotton, 190.5 x 99.1 cm)
- Silicone Hoses for water circulation
- Power Adapter
- Wireless Remote Control
Setup Instructions
Follow these steps to set up your Adamson B10 Single Bed Cooling System:
- Place the Mattress Pad: Lay the Adamson B10 mattress pad directly over your existing mattress. Ensure it is spread evenly and smoothly. The pad is designed for versatile use on twin beds, and can also be used on one side of King/Queen beds.
- Position the Cooling Unit: Place the Adamson B10 cooling unit on a stable surface next to your bed. For optimal performance, the unit's water reservoir should be positioned at a level higher than the mattress pad. This facilitates proper water circulation.
- Connect the Hoses: Connect the silicone hoses from the mattress pad to the designated inlet and outlet ports on the Adamson B10 cooling unit. Ensure these connections are firm and secure to prevent any leaks.
- Fill the Water Tank: Open the water reservoir cap on the cooling unit and carefully fill it with clean, distilled water. Do not overfill; ensure the water level is between the minimum and maximum indicators.
- Connect Power: Plug the power adapter into the cooling unit and then into a suitable electrical outlet.
Image: Easy setup steps for the Adamson B10 cooling system.
Image: The Adamson B10 mattress pad showing versatile use on different bed sizes.
Operating Instructions
Once the system is set up, you can begin operation:
- Power On: Press the power button on the cooling unit or the wireless remote control to turn on the system. The unit will begin circulating water.
- Adjust Temperature: Use the controls on the unit or the remote to adjust the cooling intensity. The system can reduce mattress temperature by 7 to 12°F (approximately 7 to -11.1 °C).
- Wireless Remote Control: The included wireless remote allows you to conveniently control the unit's functions without leaving your bed.
- Power Off: Press the power button again to turn off the system when not in use.
Image: Wireless remote control for convenient operation.
Image: Illustration of the water cooling system's effect on mattress temperature.
Maintenance
Regular maintenance ensures the longevity and efficiency of your Adamson B10 system:
- Water Tank: Regularly check the water level in the reservoir and refill with distilled water as needed. It is recommended to clean the water tank every 2-4 weeks to prevent algae or mineral buildup. Drain the old water, rinse the tank thoroughly, and refill with fresh distilled water.
- Mattress Pad: The 100% cotton mattress pad requires dry cleaning only. Do not machine wash or tumble dry.
- Unit Exterior: Wipe the exterior of the cooling unit with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Hoses: Periodically inspect the silicone hoses for any kinks, damage, or leaks. Ensure they are securely connected.
Image: The soft and comfortable 100% cotton mattress pad.
Troubleshooting
If you encounter any issues with your Adamson B10, please refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Unit is not turning on | No power, loose connection | Check power adapter connection to unit and wall outlet. Ensure outlet is functional. |
| No cooling effect | Low water level, kinked hoses, unit not positioned correctly | Refill water tank with distilled water. Check hoses for kinks or blockages. Ensure cooling unit is higher than the mattress pad. |
| Unit is noisy | Air in system, low water level, unit vibration | Ensure water tank is adequately filled. Allow unit to run for a few minutes to purge air. Place unit on a stable, anti-vibration mat if necessary. |
| Water leakage | Loose hose connections, damaged hose/unit | Check all hose connections and tighten if loose. Inspect hoses and unit for visible damage. If damage is found, discontinue use and contact support. |
If the problem persists after attempting these solutions, please contact Adamson customer support for further assistance.
Image: Lab-tested efficiency showing temperature reduction.
Specifications
- Model: Adamson B10
- Mattress Pad Dimensions (L x W x H): 190.5 x 99.1 x 1.5 cm (75 x 39 x 0.6 inches)
- Item Weight: 1.3 Kilograms (2.87 lbs)
- Mattress Pad Material: 100% Cotton
- Special Feature: Cooling
- Cooling Range: Reduces mattress temperature by 7 to 12°F (approx. 7 to -11.1 °C)
- Energy Consumption: 8 Wh (compared to 800 Wh for standard AC)
- Care Instructions (Mattress Pad): Dry clean only
- Water Resistance Level: Not waterproof (for the unit)
Image: Adamson B10 energy efficiency, saving money.
Image: Benefits of investing in your health with the Adamson B10.
Warranty and Support
Adamson is committed to providing quality, durable appliances with exceptional customer care. Your Adamson B10 Single Bed Cooling System comes with a 5-Year Protection plan, ensuring peace of mind.
For any questions, concerns, or technical support, our dedicated 24/7 customer service team is available to assist you. Please refer to the contact information provided with your purchase or visit our official website for support details.
Image: Adamson's commitment to quality and 5-year protection.