Enhulk 58V 16-Inch Cordless String Trimmer Instruction Manual

Introduction

This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your Enhulk 58V 16-Inch Cordless String Trimmer. Please read this manual thoroughly before using the product and keep it for future reference.

The Enhulk string trimmer is designed for ease of use and powerful performance, offering a virtually maintenance-free experience without the need for gas or oil, and producing zero emissions. It ensures instant starts and quiet operation while delivering the necessary power for your trimming tasks.

Important Safety Information

Always wear eye protection, long pants, and closed-toe shoes. Keep a safe distance from others and objects while operating the trimmer.

Before each use, inspect the trimmer for any damage or loose parts. Ensure the battery pack is securely installed and fully charged. Do not operate the trimmer in wet conditions or near flammable liquids or gases.

Setup

Assembly

Your Enhulk string trimmer features a foldable shaft for convenient storage and transport. To assemble, unfold the shaft until it locks into place. Ensure all connections are secure before proceeding.

Adjusting the Hand Grip

The trimmer is equipped with a tool-free adjustable hand grip. Loosen the adjustment knob, position the grip to a comfortable operating height and angle, and then tighten the knob securely. This allows for optimal control and comfort during use.

Battery Installation

Insert a fully charged Enhulk 58V battery pack into the battery compartment until it clicks into place. Ensure it is firmly seated to prevent dislodgement during operation.

Operating Instructions

Starting the Trimmer

To start the trimmer, ensure the battery is installed and press the safety lock-out button, then squeeze the variable speed trigger. Release the safety lock-out button once the trimmer is running.

Selecting Speed Modes (EZ-HMI LED Control Panel)

The EZ-HMI LED Control Panel allows for easy switching between three cutting modes: ECO, HIGH, and TURBO. Press the 'MODE' button to cycle through the settings. The LED indicators will show the currently selected mode.

• ECO Mode: For lighter trimming tasks and extended battery run time (up to 45 minutes).
• HIGH Mode: For general trimming of moderate grass and weeds.
• TURBO Mode: Provides maximum power for tackling thick grass and dense weeds.

Trimming Techniques

Utilize the 16-inch cutting path for efficient coverage. For best results, use a sweeping motion, moving the trimmer from side to side. The pro-grade dual 0.095” line is designed to handle thick grass and weeds effectively.

Maintenance

General Care

The Enhulk string trimmer features an advanced brushless motor, which requires no maintenance. After each use, clean the trimmer head and shield to remove grass clippings and debris. Ensure the air vents are clear to prevent overheating.

Line Replacement (Quick Line Load)

The patented quick line load bump-feed trimmer head allows for fast and hassle-free line reloading without disassembly. Simply feed the new line through the eyelets and bump the head on the ground while the trimmer is running to advance the line. Compatible with 0.095" and 0.080" trimmer line.

Troubleshooting

If your trimmer is not operating as expected, please review the following common issues:

• Trimmer does not start: Ensure the battery is fully charged and properly seated. Check that the safety lock-out button is pressed before squeezing the trigger.
• Reduced cutting performance: The trimmer line may be too short or worn. Advance the line using the bump-feed mechanism or replace it if necessary. Ensure the cutting head is free of tangled debris.
• Overheating: If the trimmer stops unexpectedly, it may be due to overheating. Allow the unit to cool down and ensure the air vents are clear of obstructions.

For issues not covered here, please contact Enhulk customer support.

Specifications

Warranty and Support

Enhulk offers a 4-year tool warranty and a 2-year battery warranty for this product. Please retain your proof of purchase for warranty claims.

Customer Care

For any product questions, technical assistance, or warranty inquiries, please contact Enhulk customer support:

• Email: service@enhulktools.com
• Hotline Service: 1(877) 750-3787