Introduction
This manual provides essential instructions for the safe and efficient use of your Faber Prince Plus 3BB BK 3 Burner Cooktop. Please read this document thoroughly before installation, operation, and maintenance to ensure proper functioning and longevity of your appliance. Keep this manual for future reference.
Image: Faber Prince Plus 3BB BK 3 Burner Cooktop, showcasing its sleek design and three burners.
Setup and Installation
Proper installation is crucial for the safe and efficient operation of your cooktop. This appliance is designed for countertop installation.
Unpacking
Carefully remove all packaging materials. Inspect the cooktop for any signs of damage. Report any damage to your retailer immediately.
Placement
- Ensure the installation area is well-ventilated.
- Place the cooktop on a stable, flat, and heat-resistant surface.
- Maintain adequate clearance from walls and overhead cabinets as per local regulations.
Gas Connection
This cooktop features a 360° Swivel Type Brass Gas Inlet, allowing flexible cylinder placement. Connect the cooktop to a Liquefied Petroleum Gas (LPG) supply using a certified gas hose and regulator. Ensure all connections are tight and leak-free. It is recommended that gas connections be performed by a qualified technician.
Image: Detail of the 360° Swivel Type Brass Gas Inlet, illustrating its rotational capability for convenient gas cylinder placement.
Components Included
The product package includes:
- 1 Gas Stove
- 1 Warranty Card
- 1 User Manual (this document)
- Cleaning Pin
- Batti Stand
Operating Instructions
Your Faber cooktop is equipped with three brass burners and manual ignition for reliable performance.
Burner Types
The cooktop features three brass burners: one small, one medium, and one jumbo burner, designed for various cooking needs.
Image: Close-up of a forged brass burner with blue flame, highlighting its design for efficient heat delivery.
Manual Ignition
- Ensure the gas supply is open.
- Press and turn the desired burner knob counter-clockwise to the 'ON' position.
- Immediately bring a lit matchstick or gas lighter close to the burner to ignite the flame.
- Adjust the flame intensity by rotating the knob between the 'HIGH' and 'LOW' settings.
- To turn off, rotate the knob clockwise to the 'OFF' position.
Safety Features
The cooktop is equipped with Anti-Leak Technology to enhance safety during operation. Always ensure proper ventilation when using the cooktop.
Maintenance and Care
Regular cleaning and maintenance will ensure the longevity and optimal performance of your cooktop.
Cleaning the Glass Surface
- Allow the cooktop to cool completely before cleaning.
- Use a soft cloth or sponge with mild detergent and warm water.
- Avoid abrasive cleaners, scouring pads, or harsh chemicals that can scratch the toughened black glass surface.
- Wipe dry with a clean cloth to prevent water spots.
Cleaning Burners and Pan Supports
The cooktop features MS Powder Coated pan supports and brass burners. These components are removable for easier cleaning.
Image: Close-up of a stable, non-slip pan support, designed to securely hold cookware.
- Remove the pan supports and burner components (burner caps and bases).
- Wash them with warm soapy water. For stubborn stains, a non-abrasive scrub brush can be used.
- Ensure all parts are completely dry before reassembling them. Moisture can affect ignition.
- The pan supports are designed with a protective flame guard for uniform heating and stability.
Image: Pan support with a protective flame guard, illustrating its design for even heat distribution and wind protection.
Troubleshooting Guide
Before contacting customer support, please refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Burner does not ignite | No gas supply Burner components are wet or clogged Ignition pin is dirty or damaged | Check gas cylinder and regulator Ensure burner caps and bases are dry and clean Clean the ignition pin with a dry cloth |
| Uneven flame | Burner ports are clogged Burner cap is not seated correctly | Clean burner ports with a cleaning pin Ensure burner cap is properly aligned and seated |
| Gas smell detected | Gas leak from connections Burner not fully off | Immediately turn off gas supply. Ventilate the area. Do not operate electrical switches. Contact a qualified technician. Ensure all burner knobs are in the 'OFF' position. |
Product Specifications
| Feature | Detail |
|---|---|
| Brand | Faber |
| Model Number | 106.0689.130 |
| Heating Elements | 3 |
| Colour | Black |
| Power Source | Gas Powered |
| Fuel Type | Liquefied Petroleum Gas (LPG) |
| Special Features | Cool Touch, Manual Ignition |
| Burner Type | Gas (Brass Burners: 1 Small, 1 Medium, 1 Jumbo) |
| Control Type | Knob |
| Installation Type | Countertop |
| Item Dimensions (D x W x H) | 38D x 77W x 11H Centimeters |
| Item Weight | 11200 Grams |
| Heater Surface Material Type | Toughened Black Glass (8mm) |
| Material Type | Glass |
| Pan Support | MS Powder Coated, Stable Non-slip |
| Country Of Origin | India |
Warranty Information
Your Faber Prince Plus 3BB BK 3 Burner Cooktop comes with the following warranty:
- Comprehensive Warranty: 2 Years
- Warranty on Glass and Burners: 5 Years
- Warranty on Valve: 2 Years
Please retain your purchase receipt and warranty card for any warranty claims. The warranty covers manufacturing defects under normal use conditions. For detailed terms and conditions, refer to the warranty card included with your product.
Customer Support
For any queries, service requests, or technical assistance, please contact Faber customer support:
- Customer Service Number: 1800-209-3484
- Manufacturer: Franke Faber India Pvt.Ltd.
- Manufacturer Address: 1086/1/2, SANASWADI, TAL - SHIRUR, PUNE - 412208, MAHARASHTRA, INDIA
When contacting support, please have your model number (106.0689.130) and purchase details ready.