1. Introduction
Thank you for choosing the AQQA Submersible Water Pump. This manual provides essential information for the safe and efficient operation, installation, and maintenance of your pump. Please read these instructions thoroughly before use and retain them for future reference.
This pump is designed for various applications including aquariums, fish tanks, ponds, hydroponics, and fountains, offering adjustable water flow and high lift capabilities.
2. Safety Instructions
To ensure safe operation and prevent injury or damage, please observe the following safety precautions:
- Always disconnect the power supply before performing any maintenance, installation, or cleaning.
- Ensure the voltage and frequency of the power supply match the specifications indicated on the pump's label.
- Do not operate the pump without water. The pump is equipped with run-dry protection, but prolonged dry operation should be avoided.
- Do not lift the pump by its power cord.
- Ensure the pump is fully submerged in water during operation to prevent overheating.
- Keep the power cord away from sharp objects and hot surfaces.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- For indoor use only, unless specified otherwise for outdoor pond applications.
3. Product Features
- 360° Bottom Intake Design: Efficiently draws water from all directions, capable of pumping water down to less than 0.39 inches (1cm). Designed to pass debris and fish waste up to 1/5 inch, promoting cleaner water.
- Safe and Quiet Operation: Features a run-dry protection system that automatically shuts off the pump if the water level is too low or motor temperature reaches 85°C, preventing burnout. The magnetic drive motor and sealed housing ensure quiet operation.
- High Lift & Adjustable Waterflow: Provides a maximum lift height of up to 11 feet (for 55W model) and a maximum flow rate of 800 GPH (for 55W model). Equipped with 2 nozzles and a control valve for customizable water flow.
- Easy to Disassemble and Clean: Designed for tool-free disassembly, simplifying routine cleaning and maintenance.
- Wide Application: Suitable for various uses including water circulation, water removal, fountains, pool draining, aquariums, fish tanks, ponds, and hydroponics.
4. Package Contents
Please check the package to ensure all items are present and undamaged:
- AQQA Submersible Water Pump (1 unit)
- Output Nozzles (2 units, varying sizes)
- Suction Cups (pre-attached or separate)
Image: The AQQA submersible water pump shown with its two included output nozzles.
5. Setup Instructions
Follow these steps to set up your AQQA submersible water pump:
- Choose Placement: The pump can be placed vertically or horizontally. Ensure the suction cups are firmly attached to a clean, smooth surface at the bottom or side of your tank or pond.
- Attach Nozzle: Select the appropriate nozzle size for your application and securely attach it to the pump's outlet.
- Submerge Pump: Place the pump into the water, ensuring it is fully submerged. The water level must be at least 1cm (0.39 inches) above the pump's intake.
- Connect Tubing (if applicable): If using with external tubing for fountains, water draining, or wave making, connect the tubing to the nozzle.
- Connect Power: Plug the pump into a suitable power outlet. The pump will begin operating.
Image: Visual guide demonstrating vertical and horizontal mounting options, as well as applications for fountain and water draining.
6. Operating Instructions
Once the pump is set up and powered on, you can adjust its performance:
- Adjust Water Flow: Locate the control valve on the pump (if applicable to your model) and slide it to increase or decrease the water flow rate according to your needs.
- Monitor Water Level: Ensure the water level remains above the minimum 1cm mark to prevent the pump from running dry. The pump's run-dry protection will automatically shut it off if the water level becomes too low and the motor temperature reaches 85°C. It will restart once the water level is restored and the motor cools.
Image: Close-up of the pump illustrating the adjustable water flow mechanism.
7. Maintenance
Regular cleaning and maintenance are crucial for the longevity and efficient operation of your pump. It is recommended to clean the pump at least once a month.
- Disconnect Power: Always unplug the pump from the power outlet before cleaning.
- Disassemble: The pump is designed for tool-free disassembly. Carefully remove the filter cover, then the impeller cover, and finally the impeller itself.
- Clean Components: Rinse all parts (filter cover, impeller, impeller cover, nozzles) under clean water to remove any debris, algae, or mineral buildup. Use a small brush if necessary to clean tight spaces.
- Inspect: Check the impeller for any signs of wear or damage. Ensure the ceramic shaft is clean and free of obstructions.
- Reassemble: Carefully reassemble the pump in reverse order, ensuring all parts fit securely.
Image: Step-by-step visual guide for disassembling the pump for cleaning.
8. Troubleshooting
If you encounter issues with your AQQA submersible water pump, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Pump does not start | No power; Impeller jammed; Run-dry protection activated | Check power connection; Disconnect power, clean impeller; Ensure sufficient water level. |
| Reduced water flow | Clogged intake/nozzle; Impeller dirty; Water level too low | Clean intake and nozzle; Clean impeller; Ensure sufficient water level. |
| Pump is noisy | Debris in impeller; Impeller worn; Not fully submerged | Clean impeller; Inspect impeller for damage and replace if necessary; Ensure pump is fully submerged. |
| Pump stops intermittently | Run-dry protection activated; Overheating | Ensure sufficient water level; Check for obstructions causing overheating. |
9. Specifications
Technical specifications for the AQQA 55W 800GPH Submersible Water Pump:
| Specification | Value |
|---|---|
| Model | GCA-AQ077-55W-CA |
| Power | 55W |
| Maximum Flow Rate | 800 GPH (3000 L/H) |
| Maximum Lift Height | 11 Feet |
| Sound Level | 25 dB |
| Material | Acrylonitrile Butadiene Styrene (ABS) |
| Power Source | AC |
| Package Dimensions | 5.83 x 5.79 x 4.72 inches |
| Item Weight | 3.12 pounds |
Image: Detailed specifications for various AQQA pump models, including the 55W 800GPH version.
10. Warranty and Support
For warranty information or technical support, please refer to the product packaging or contact AQQA customer service directly. Keep your purchase receipt as proof of purchase.
For further assistance, visit the official AQQA store or contact their support channels.
