MOTO GUARD HG24

Download PDF
Contents

Motoguard HG24 Handguards User Manual

Compatible with BMW R NineT/Pure/Scrambler/Urban GS 2014-2021

1. Introduction

Product Overview

Thank you for choosing Motoguard HG24 Handguards. These handguards are designed to provide superior protection for your hands while riding, shielding them from wind, rain, and debris. Constructed from durable ABS plastic and reinforced with a robust steel bracket, they ensure a secure fit and enhanced riding comfort. This manual provides essential information for installation, maintenance, and safe use of your new handguards.

2. Safety Information

  • Always ensure all components are securely fastened before riding. Loose parts can cause accidents.
  • Regularly inspect handguards for any signs of damage or wear. Replace damaged parts immediately.
  • Installation should be performed by a qualified technician if you are unsure about any steps.
  • These handguards are not suitable for BMW models equipped with Dual Clutch Transmission (DCT). Verify your motorcycle's transmission type before installation.
  • Do not modify the handguards or mounting hardware. Unauthorized modifications can compromise safety and performance.

3. Package Contents

Please check the package to ensure all items listed below are present and undamaged:

  • 1x Left Handguard (ABS Plastic)
  • 1x Right Handguard (ABS Plastic)
  • 2x Steel Mounting Brackets
  • Necessary Mounting Hardware (bolts, washers, spacers)
Motoguard HG24 Handguards and Mounting Hardware

Image 1: All components included in the Motoguard HG24 Handguards package.

4. Setup and Installation

Tools Required

  • Hex Key Set (Allen wrenches)
  • Torque Wrench (recommended for precise tightening)
  • Socket Wrench Set (if applicable for handlebar end weights)
  • Threadlocker (medium strength, optional but recommended)

Installation Steps

  1. Prepare the Handlebar: If your motorcycle has handlebar end weights, carefully remove them. Clean the handlebar area where the handguards will be mounted.
  2. Attach Mounting Bracket: Secure the steel mounting bracket to the handlebar. Ensure it is positioned correctly and does not interfere with brake or clutch levers. Hand-tighten the bolts initially.
  3. Mount the Handguard: Align the ABS plastic handguard with the mounting bracket. Use the provided bolts and washers to attach the handguard to the bracket. Do not fully tighten yet.
  4. Adjust Position: Adjust the angle and position of the handguard to ensure maximum coverage and clearance for your hands and controls. Ensure full range of motion for steering and levers.
  5. Tighten All Fasteners: Once satisfied with the position, progressively tighten all bolts. If using a torque wrench, refer to your motorcycle's service manual for appropriate torque specifications for handlebar accessories. Apply threadlocker if desired for added security.
  6. Repeat for Other Side: Follow the same steps for the opposite side of the handlebar.
  7. Final Check: After installation, double-check all bolts for tightness. Ensure the handguards do not impede any controls or steering. Test the steering from lock to lock to confirm no interference.
Motoguard HG24 Handguard installed on left side of motorcycle handlebar

Image 2: Motoguard HG24 Handguard installed on the left side of a motorcycle handlebar.

Motoguard HG24 Handguard installed on right side of motorcycle handlebar

Image 3: Motoguard HG24 Handguard installed on the right side of a motorcycle handlebar.

5. Maintenance

Proper maintenance will extend the life of your Motoguard Handguards:

  • Cleaning: Clean the handguards regularly with mild soap and water. Avoid harsh chemicals or abrasive cleaners, which can damage the ABS plastic.
  • Inspection: Periodically check all mounting bolts for tightness, especially after off-road riding or long trips.
  • Damage Check: Inspect the handguards and brackets for any cracks, bends, or other signs of damage. Replace any damaged components immediately to maintain protection.

6. Troubleshooting

Refer to the table below for common issues and their solutions:

ProblemPossible CauseSolution
Handguards feel loose after installation.Bolts not tightened sufficiently.Re-tighten all mounting bolts securely. Consider using threadlocker.
Interference with brake/clutch levers or steering.Incorrect positioning of handguard or bracket.Loosen mounting bolts, adjust handguard position for proper clearance, then re-tighten.
Handguards do not fit my BMW R NineT model.Motorcycle has Dual Clutch Transmission (DCT).These handguards are not compatible with DCT models. Verify your motorcycle's specifications.

7. Specifications

FeatureDetail
Product NameMotoguard HG24 Handguards
CompatibilityBMW R NineT/Pure/Scrambler/Urban GS (2014-2021) - Not for DCT models
MaterialHigh-quality ABS Plastic (Handguards), Steel (Brackets)
Item Weight1.41 pounds
ManufacturerMOTO GUARD
Country of OriginChina
ASINB0CR1HS9N2

8. Warranty and Support

Warranty Information

For information regarding product warranty, please refer to the terms and conditions provided at the time of purchase or contact your retailer. Keep your proof of purchase for any warranty claims.

Customer Support

If you have any questions, require assistance with installation, or encounter issues not covered in this manual, please contact MOTO GUARD customer support through the retailer's platform or the official MOTO GUARD website. Please have your product model (HG24) and purchase details ready when contacting support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.