Uetmulik Power Recliner Lift Chair Remote Control

Introduction

This manual provides essential instructions for the proper installation, operation, and maintenance of your Uetmulik Power Recliner Lift Chair Remote Control, model HC R2B 07. Please read this manual thoroughly before use to ensure safe and efficient operation.

Safety Information

Always follow these safety guidelines to prevent injury or damage:

• Always follow the assembly instructions carefully.
• Keep the remote out of reach of children and pets.
• Do not attempt to operate the chair's functions while the user is not seated securely.
• Always test the chair's functions after assembly to ensure they work properly and safely.
• Ensure the power cord and remote cable are not pinched or damaged.
• Do not expose the remote to liquids or extreme temperatures.

Product Overview

The Uetmulik HC R2B 07 is a 4-button, 5-pin replacement hand control designed for Raffel Systems power recliner lift chairs. It features a backlight for improved visibility and a 9.8ft cable for flexible positioning.

Figure 1: Front view of the Uetmulik HC R2B 07 remote control, showing the four buttons, backlight, cable, and 5-pin connector.

Figure 2: Detailed view of the remote control buttons. The top two buttons control the 'BACK' function (recline/incline), and the bottom two buttons control the 'LIFT/FOOT' function (footrest extension/retraction and chair lift).

Figure 3: Rear view of the remote control, displaying the Raffel Systems manufacturer information and model number HC R2B 07.

Setup and Installation

Follow these steps to install your new remote control:

1. Verify Compatibility: Ensure your existing recliner system uses a 5-pin connector. This remote is specifically designed for 5-pin systems. If your current remote has a different pin configuration, this replacement will not be compatible.
2. Disconnect Power: Before beginning installation, unplug your power recliner from the wall outlet to prevent electrical hazards.
3. Locate Existing Remote Cable: Find where your old remote control cable connects to the chair's motor or control box.
4. Disconnect Old Remote: Carefully unplug the old remote control cable from the chair's system.
5. Connect New Remote: Take the new Uetmulik HC R2B 07 remote control's 5-pin connector and align it with the corresponding port on your chair's motor or control box. The connector has a 90-degree angle plug designed to fit straight into the motor connector. Push firmly until it is securely seated.
6. Route Cable: Route the 9.8ft controller cable to a convenient location, ensuring it is not tangled, pinched, or obstructing any moving parts of the chair.
7. Restore Power: Plug your power recliner back into the wall outlet.
8. Test Functionality: Test all functions of the remote control (Back, Lift/Foot) to ensure proper operation.

Operating Instructions

The Uetmulik HC R2B 07 remote control features four buttons to operate your power recliner lift chair:

• BACK (Top Buttons):
  • Press the top-left button to recline the chair back.
  • Press the top-right button to bring the chair back to an upright position.
• LIFT/FOOT (Bottom Buttons):
  • Press the bottom-left button to extend the footrest and/or lift the chair.
  • Press the bottom-right button to retract the footrest and/or lower the chair.

The remote control includes a backlight for easy visibility in low-light conditions.

Maintenance

To ensure the longevity and proper function of your remote control:

• Cleaning: Wipe the remote control surface with a soft, damp cloth. Avoid using harsh chemicals or abrasive cleaners. The design allows for easy wiping and disinfection.
• Cable Care: Regularly inspect the cable for any signs of wear, cuts, or damage. Ensure the cable is not kinked or stretched excessively.
• Storage: When not in use, place the remote in a safe location where it will not be dropped or damaged.

Troubleshooting

If you encounter issues with your remote control, try the following steps:

• Remote Not Responding:
  • Ensure the chair is properly plugged into a working electrical outlet.
  • Check that the 5-pin connector of the remote control is securely plugged into the chair's motor or control box.
  • Inspect the remote control cable for any visible damage. If damaged, the remote may need replacement.
• Backlight Not Working:
  • If the remote functions but the backlight does not, this may indicate a minor electrical issue with the backlight component. The remote should still be functional.
• Chair Functions Incorrectly:
  • If the chair moves in an unexpected way, immediately release the button. Re-check the connection of the remote. If the issue persists, consult the chair's original manual or contact the chair manufacturer.

If these steps do not resolve the issue, please contact customer support.

Specifications

Warranty and Support

For warranty information or technical support, please refer to the original purchase documentation or contact the seller directly. Keep your purchase receipt for warranty claims.

For further assistance, you may visit the Uetmulik store on Amazon: Uetmulik Store