1. Introduction
Thank you for choosing the SLV New Tria 68 Round LED Spot Light. This product is designed for indoor use, providing efficient and modern illumination. This manual contains important information regarding the installation, operation, and maintenance of your new LED spot light. Please read it thoroughly before installation and keep it for future reference.
Image 1.1: SLV New Tria 68 LED spot light installed in a wooden ceiling, illuminating a wine cellar.
2. Safety Instructions
- Electrical Safety: Installation must be performed by a qualified electrician in accordance with national wiring regulations. Always disconnect power at the main circuit breaker before installation or maintenance.
- Product Integrity: Do not modify or alter the product in any way. Doing so may void the warranty and create safety hazards.
- Operating Environment: This product is designed for indoor use only. Do not expose it to moisture, extreme temperatures, or corrosive environments.
- Handling: Handle the product with care to avoid damage to the LED module or housing.
- Heat: The LED spot light may become warm during operation. Ensure adequate ventilation around the fixture.
3. Package Contents
Verify that all components are present and undamaged before proceeding with installation:
- SLV New Tria 68 LED Spot Light fixture
- LED Power Supply (Driver)
- Mounting Clips (2x)
- Instruction Manual (this document)
Image 3.1: Components of the SLV New Tria 68 LED spot light, including the light unit, power supply, and mounting clips.
4. Setup and Installation
Follow these steps for proper installation:
- Prepare the Installation Area: Ensure the power supply to the installation area is turned off at the main circuit breaker.
- Determine Cutout Size: Refer to the dimension diagram (Image 4.1) for the required ceiling cutout diameter. The recommended cutout diameter is approximately 6.8 cm.
- Create Cutout: Using an appropriate tool, create a circular cutout in the ceiling or mounting surface according to the specified diameter.
- Connect Wiring: Connect the LED power supply (driver) to the main electrical supply (220V). Ensure correct polarity and secure all connections using appropriate connectors. The output of the LED driver should then be connected to the LED spot light fixture.
- Insert Fixture: Gently push the mounting clips on the side of the spot light upwards. Insert the spot light into the cutout. The clips will spring back into place, securing the fixture to the ceiling.
- Adjust Direction (if applicable): The New Tria 68 features an adjustable light head. Once installed, you can gently tilt the inner ring to direct the light beam as desired.
- Restore Power: Once the fixture is securely installed and all connections are checked, restore power at the main circuit breaker.
Image 4.1: Technical drawing showing the dimensions of the SLV New Tria 68 LED spot light, including cutout diameter (Ø 6.8 cm) and overall diameter (Ø 8.2 cm), and height (3.8 cm).
Image 4.2: Example of SLV New Tria 68 LED spot lights installed in a modern interior setting.
5. Operating Instructions
The SLV New Tria 68 LED Spot Light operates by a standard wall switch connected to its power supply. Once installed and wired correctly:
- Turning On/Off: Use the connected wall switch to turn the light fixture on or off.
- Light Direction: Gently adjust the inner light module to direct the light beam to your desired area. Avoid excessive force when adjusting.
6. Maintenance
The SLV New Tria 68 LED Spot Light requires minimal maintenance.
- Cleaning: Ensure the power is off before cleaning. Use a soft, dry, or slightly damp cloth to wipe the surface of the fixture. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish.
- LED Module: The integrated LED module is designed for long-term use and is not user-replaceable. Do not attempt to open the fixture or replace the LED module.
7. Troubleshooting
If you encounter issues with your SLV New Tria 68 LED Spot Light, refer to the following table:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power supply. Loose wiring connection. Faulty LED driver. | Check the circuit breaker. Ensure all wiring connections are secure (power off first). Contact a qualified electrician or SLV support. |
| Light flickers. | Unstable power supply. Loose connection. Incompatible dimmer (if applicable). | Check power stability. Verify wiring connections. Ensure dimmer is compatible with LED fixtures (if used). |
| Reduced light output. | Dust accumulation. Product nearing end of life. | Clean the fixture surface. Consider replacement if cleaning does not resolve the issue. |
If the problem persists after attempting these solutions, please contact SLV customer support or a qualified electrician.
8. Specifications
| Feature | Specification |
|---|---|
| Brand | SLV |
| Model Number | 1007386 (New Tria 68) |
| Product Dimensions (L x W x H) | 8.2 x 8.2 x 4 cm |
| Item Weight | 193 grams |
| Style | Modern |
| Color | Black (Shade Color), Warm White (Light Color) |
| Material | Metal |
| Finish Type | Raw |
| Number of Light Sources | 1 |
| Voltage | 220 Volts |
| Light Source Type | LED |
| Luminous Flux | 705 lumen |
| Power | 8.3 Watts |
| Battery(ies) Required | No |
| Indoor/Outdoor Use | Indoor |
| Luminaire Shape | Spotlight |
9. Warranty Information
Specific warranty information for the SLV New Tria 68 LED Spot Light is not provided in the product details. Please refer to the retailer or manufacturer's official website for the most up-to-date warranty terms and conditions. Keep your proof of purchase for any warranty claims.
10. Support
For technical assistance, spare parts, or further inquiries regarding your SLV New Tria 68 LED Spot Light, please contact:
- Manufacturer: SLV GmbH
- Website: www.slv.com (Please check for local contact information)
- Retailer: Contact the retailer from whom you purchased the product.
