Fruyyzl AnYu126 Ergonomic Gaming Chair User Manual

1. Introduction

Thank you for choosing the Fruyyzl AnYu126 Ergonomic Gaming Chair. This manual provides essential information for the safe assembly, operation, and maintenance of your new chair. Please read these instructions carefully before use and retain them for future reference.

The Fruyyzl AnYu126 gaming chair is designed for comfort and support during extended periods of sitting, whether for gaming or office work. It features an ergonomic design with adjustable lumbar and neck support, a retractable footrest, and a recline function to enhance your experience.

2. Safety Information

• Maximum Weight Capacity: This chair is designed to support a maximum weight of 350 lbs (approximately 158 kg). Exceeding this limit may cause damage to the chair and potential injury.
• BIFMA Certified: The chair's components are BIFMA certified, ensuring durability and safety standards.
• Assembly: Assemble the chair strictly according to the instructions. Ensure all screws and bolts are securely tightened before use.
• Children and Pets: Keep children and pets away from the assembly area. Small parts can be a choking hazard.
• Proper Use: Do not stand on the chair. Use the chair only for its intended purpose of sitting.
• Maintenance: Regularly check all connections and moving parts for wear or looseness. Tighten as necessary.

3. Package Contents

Before beginning assembly, please ensure all parts are present and undamaged. If any parts are missing or damaged, contact customer support immediately.

• Backrest
• Seat Base
• Armrests (2)
• Gas Lift Cylinder
• Star Base
• Casters (5)
• Mechanism Plate
• Lumbar Cushion
• Neck Cushion
• Retractable Footrest
• Hardware Pack (screws, washers, Allen key)
• Instruction Manual

4. Setup and Assembly

Assembly typically takes around 30 minutes. Follow these general steps. Refer to the included diagram for visual guidance.

1. Attach Casters to Star Base: Insert the five casters into the holes at the end of each leg of the star base until they click securely into place.
2. Insert Gas Lift: Place the gas lift cylinder into the center hole of the star base. Place the gas lift cover over the cylinder.
3. Attach Mechanism Plate to Seat Base: Align the mechanism plate with the pre-drilled holes on the underside of the seat base. Ensure the front of the mechanism faces the front of the seat. Secure with screws.
4. Attach Armrests to Seat Base: Secure the armrests to the sides of the seat base using the provided screws.
5. Attach Backrest to Seat Base: Connect the backrest to the seat base using the metal brackets and screws. Ensure a firm connection.
6. Attach Footrest: Slide the retractable footrest into its designated slots under the seat.
7. Connect Seat Assembly to Gas Lift: Carefully place the assembled seat onto the gas lift cylinder, ensuring it is centered and stable.
8. Attach Cushions: Secure the neck and lumbar cushions to the backrest using their elastic straps.

Figure 4.1: Key functional components for assembly and operation.

5. Operating Instructions

Your Fruyyzl AnYu126 chair offers several adjustment options for personalized comfort.

5.1 Height Adjustment

To adjust the chair's height, locate the lever on the right side, beneath the seat. While seated, pull the lever up to lower the chair. To raise the chair, stand up slightly and pull the lever up. Release the lever to lock the height.

5.2 Recline Function

The backrest can be reclined from 90 to 155 degrees. Locate the recline lever on the right side of the chair, near the armrest. Pull the lever up and lean back to your desired angle. Release the lever to lock the backrest in position. To return to an upright position, pull the lever and lean forward.

Figure 5.1: Adjustable recline and height mechanism.

5.3 Retractable Footrest

To use the footrest, pull it out from underneath the seat. Extend it to your preferred length. To retract, push it back under the seat until it is fully stored.

5.4 Lumbar and Neck Cushions

The lumbar and neck cushions are adjustable. Slide them up or down along the backrest straps to find the most comfortable position for your spine and neck.

Figure 5.2: Ergonomic design for comprehensive body support.

6. Maintenance

Regular maintenance will prolong the life and appearance of your gaming chair.

• Cleaning: The chair is made of synthetic leather, which is waterproof. For general cleaning, wipe the surface with a soft, damp cloth. For stubborn stains, use a mild soap solution and wipe dry immediately. Avoid harsh chemicals or abrasive cleaners.
• Hardware Check: Periodically check all screws and bolts (every 3-6 months) to ensure they are tight. Re-tighten if necessary to prevent wobbling or instability.
• Caster Care: Keep the casters clean by removing any hair or debris that may accumulate around them. This ensures smooth movement.
• Avoid Direct Sunlight: Prolonged exposure to direct sunlight can cause the synthetic leather to fade or crack. Position the chair away from direct sunlight if possible.

Figure 6.1: Synthetic leather material with waterproof properties.

7. Troubleshooting

If you encounter any issues with your chair, refer to the following common problems and solutions:

• Chair is Wobbly:
  Solution: Check all assembly screws and bolts. Tighten any loose connections. Ensure the star base is fully seated on the gas lift.
• Chair Does Not Adjust Height:
  Solution: Ensure the gas lift lever is fully engaged. Check if the gas lift cylinder is properly inserted into the mechanism plate and star base. If the issue persists, the gas lift may need replacement.
• Backrest Does Not Recline/Lock:
  Solution: Ensure the recline lever is fully engaged. Check for any obstructions in the recline mechanism.
• Casters Not Rolling Smoothly:
  Solution: Remove any debris (hair, dust) from the caster wheels. Ensure casters are fully inserted into the star base.
• Squeaking Noises:
  Solution: Apply a small amount of silicone lubricant to moving parts, especially where metal components meet. Check and tighten all screws.

If these solutions do not resolve the issue, please contact Fruyyzl customer support.

8. Specifications

Figure 8.1: Product dimensions and weight capacity.

9. Warranty and Support

Fruyyzl is committed to providing high-quality products. For specific warranty information regarding your AnYu126 gaming chair, please refer to the warranty card included in your package or visit the official Fruyyzl website. If you have any questions, require technical assistance, or need to report a missing/damaged part, please contact Fruyyzl customer support through their official channels.