DEPSTECH DS520 Industrial Borescope Tool User Manual

1. Introduction

This manual provides instructions for the safe and effective operation of your DEPSTECH DS520 Industrial Borescope Tool. Please read this manual thoroughly before use and retain it for future reference. The DS520 is designed for inspecting hard-to-reach areas in various industrial, automotive, and household applications, featuring a 1080P dual-lens camera, a 5-inch IPS screen, and an IP67 waterproof semi-rigid cable.

2. Product Components

The DEPSTECH DS520 package includes the following items:

• 1 x DEPSTECH DS520 Endoscope Camera (with 32GB TF card pre-installed)
• 1 x 16.5ft Semi-Rigid Cable
• 1 x Type-C Charging Cable
• 1 x User Manual
• 1 x Accessory Set (Protective Cap, Magnet, Hook)
• 1 x EVA Carrying Case

3. Key Features

• 5-inch IPS Screen: Provides real-time HD observation with a 179° viewing angle.
• 1080P Dual-Lens Camera: Features both front and side cameras for comprehensive inspection.
• Split Screen Function: Allows simultaneous viewing from both front and side cameras.
• Adjustable LED Lights: Integrated lights with three brightness levels for clear imaging in dark environments.
• IP67 Waterproof: The camera probe and cable are waterproof for use in wet conditions.
• Detachable Semi-Rigid Cable: 16.5ft cable is flexible yet rigid enough to navigate tight spaces, and can be replaced with single or triple lens cables (sold separately).
• Built-in 32GB TF Card: Stores approximately 30,000 timestamped photos and videos.
• Ergonomic Design: Allows for comfortable one-handed operation.
• 2600mAh Battery: Provides up to 4 hours of continuous runtime.

4. Setup

4.1 Charging the Device

Before first use, fully charge the borescope using the provided Type-C cable and a standard USB power adapter (not included). The charging status LED indicator will show charging progress.

4.2 Inserting the TF Card

The device comes with a 32GB TF card pre-installed. If you need to replace it, ensure the device is powered off before inserting or removing the TF card into the designated slot.

4.3 Connecting the Camera Cable

Align the USB connector of the semi-rigid camera cable with the USB port on the main unit. Insert it firmly until it clicks into place. Ensure a snug fit to prevent accidental disconnection during operation.

5. Operating Instructions

5.1 Device Controls

Familiarize yourself with the buttons on the main unit:

• Power Button: Press and hold to turn the device on/off.
• Photo/Video Button: Short press to take a photo, long press to start/stop video recording.
• OK / Play Button: Confirms selections in menus or plays recorded media.
• Menu / Back Button: Accesses the menu or returns to the previous screen.
• Dim Lights / Up Button: Decreases LED brightness or navigates up in menus.
• Brighten Lights / Down Button: Increases LED brightness or navigates down in menus.
• 180° Rotate / Switch Lens Button: Short press to rotate the image 180°. Long press to switch between front camera, side camera, or split-screen view.

5.2 Powering On and Basic Operation

1. Press and hold the Power Button to turn on the borescope. The screen will display the live camera feed.
2. Adjust the LED lights using the Brighten/Dim buttons to achieve optimal illumination.
3. To switch between the front camera, side camera, or split-screen view, press and hold the 180° Rotate / Switch Lens Button.
4. To rotate the image 180 degrees, short press the 180° Rotate / Switch Lens Button.

5.3 Capturing Photos and Videos

• Taking Photos: Short press the Photo/Video Button. The image will be saved to the TF card.
• Recording Videos: Long press the Photo/Video Button to start recording. Long press again to stop. Videos are saved to the TF card.

5.4 Data Transfer

To transfer photos and videos to a computer:

1. Connect the borescope to your computer using the Type-C cable.
2. The device will enter data transmission mode. The screen may display "No Signal" temporarily.
3. Your computer should recognize the device as a removable storage drive.
4. Access the files on the TF card and transfer them as needed.

6. Maintenance

6.1 Cleaning

• Camera Lens: Gently wipe the camera lens with a soft, dry cloth. For stubborn dirt, use a lens cleaning solution on a microfiber cloth.
• Cable: After use in dirty or wet environments, wipe the semi-rigid cable clean with a damp cloth. Ensure it is dry before storage.
• Main Unit: Clean the screen and main unit with a soft, dry cloth. Avoid using abrasive cleaners or solvents.

6.2 Storage

When not in use, store the borescope and its accessories in the provided EVA carrying case. Keep the device in a cool, dry place, away from direct sunlight and extreme temperatures.

6.3 Waterproofing

The camera probe and cable are IP67 waterproof, meaning they are protected against dust and can withstand immersion in water up to 1 meter for 30 minutes. The main unit is not waterproof; avoid exposing it to liquids.

7. Troubleshooting

• Device does not power on: Ensure the battery is charged. Connect the device to a power source using the Type-C cable and try again.
• No image on screen: Check if the camera cable is securely connected to the main unit. Ensure the cable is not damaged.
• Image is blurry or dark: Adjust the LED brightness using the dedicated buttons. Ensure the camera lens is clean. Check the focal length specifications (Front camera: 3-10cm; Side camera: 2-6cm) to ensure the object is within range.
• "No Signal" appears during data transfer: This is normal for a few seconds when entering data transmission mode. If it persists, ensure the Type-C cable is properly connected to both the borescope and the computer.
• Camera cable disconnects occasionally: Ensure the USB plug connecting the camera cable to the screen is inserted tightly.

8. Specifications

9. Warranty and Support

The DEPSTECH DS520 Industrial Borescope Tool comes with a 2-year warranty. For technical support, warranty claims, or any inquiries, please contact DEPSTECH customer service. You can find more information and support resources on the official DEPSTECH Store.