Introduction
This manual provides detailed instructions for the assembly, operation, and maintenance of your RASTAR 99600 1/18 scale Porsche 911 GT2 RS Remote Control Car Building Kit. Please read this manual thoroughly before beginning assembly or operation to ensure proper function and safety.
Image: The fully assembled RASTAR 99600 Porsche 911 GT2 RS remote control car, showcasing its detailed design and accompanying remote control.
Package Contents
Verify that all components listed below are present in your package:
- Building kits (1 set, includes stickers)
- Remote controller (1)
- Instruction Manual (1)
- Note: 5 AA Batteries are required (3 for the car, 2 for the controller) and are not included.
Image: All components of the RASTAR 99600 kit, including building parts, remote control, and manual, neatly arranged.
Initial Setup
Battery Installation
- For the Car: Locate the battery compartment on the underside of the car chassis. Use a small screwdriver (not included) to open the battery cover. Insert 3 AA batteries, ensuring correct polarity (+/-). Securely close the battery cover.
- For the Remote Controller: Locate the battery compartment on the back of the remote control. Open the cover and insert 2 AA batteries, observing correct polarity. Close the cover securely.
Tire Selection
The kit includes two sets of tires: one for drifting (smooth) and one for racing (treaded). Choose the appropriate set based on your desired driving experience. Refer to the assembly section for instructions on changing tires.
Image: A close-up view of the two distinct tire types included with the kit: slick tires for drifting and treaded tires for enhanced grip during racing.
Assembly Instructions
Follow the step-by-step guide provided in the included manual to construct your Porsche 911 GT2 RS RC car. Ensure all parts are securely connected. Pay close attention to the illustrations for correct placement of components.
Key Assembly Points:
- Chassis Assembly: Begin by assembling the main chassis components as indicated in the manual.
- Motor and Gearbox: Carefully install the motor and connect it to the gearbox. Ensure all wiring is correctly routed and secured.
- Wheel and Axle Installation: Attach the axles and wheels. If changing tires, remove the small screw in the center of each wheel to swap them.
- Body Panels and Details: Affix the body panels, including doors, hood, and rear wing. Apply the provided stickers for authentic detailing.
- Electronics Connection: Connect the battery pack to the car's electronic components.
Image: An exploded diagram illustrating the various components of the RASTAR 99600 kit, showing how they fit together during assembly.
Images: Detailed views of the car's interior and illuminated front lights, highlighting the model's realistic features.
Operating Instructions
Pairing the Remote Control
- Ensure fresh batteries are installed in both the car and the remote control.
- Turn on the car using the ON/OFF switch located on its underside. The car's lights may blink, indicating it's searching for a signal.
- Turn on the remote control. The indicator light on the remote should become solid, and the car's lights should stop blinking, confirming a successful connection.
Basic Controls
- Forward/Reverse: Use the trigger on the remote control. Pull to move forward, push to move backward.
- Steering: Use the steering wheel on the remote control to turn left or right.
- Speed Modes: The remote control may feature buttons to switch between low and high-speed modes. Low speed is recommended for indoor use and beginners.
- Lights: Some models may have a button on the remote to control the car's headlights and taillights.
Image: The RASTAR 99600 RC car positioned next to its remote control, illustrating the primary components for operation.
Maintenance
- Cleaning: Use a soft, dry cloth to clean the car's body. Avoid water or harsh chemicals.
- Battery Care: Remove batteries from both the car and remote control when not in use for extended periods to prevent leakage.
- Storage: Store the car and remote in a cool, dry place away from direct sunlight and extreme temperatures.
- Inspection: Periodically check for loose screws or damaged parts. Replace any broken components to maintain optimal performance.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Car does not respond to remote. | Low or dead batteries in car/remote; improper pairing. | Replace batteries; re-pair car and remote (refer to "Pairing the Remote Control"). |
| Car moves slowly or inconsistently. | Low batteries in car; obstruction in wheels/gears. | Replace car batteries; check and clear any obstructions. |
| Car pulls to one side. | Steering trim adjustment needed. | Adjust the steering trim dial on the underside of the car until it drives straight. |
Specifications
- Model Number: 99600
- Scale: 1:18
- Recommended Age: 6 - 10 years
- Power Source: 5 AA batteries required (3 for car, 2 for controller - not included)
- Approximate Dimensions: 26.3 cm (length) x 11.1 cm (width) x 7.2 cm (height)
- Approximate Item Weight: 1.94 pounds
- Features: Full function remote control (forward, reverse, stop, turn left & right), low speed for indoor/outdoor play, officially licensed by Porsche.
Image: A visual representation of the RASTAR 99600 RC car with its key dimensions labeled in centimeters.
Safety Information
- Always operate the RC car in a safe, open area, away from people, pets, and obstacles.
- Do not operate near streets, busy roads, or water.
- Adult supervision is recommended for younger users.
- Do not touch moving parts (wheels, gears) during operation.
- Avoid dropping or subjecting the car to heavy impacts.
- Dispose of used batteries responsibly.
Warranty and Support
For warranty information or technical support, please refer to the contact details provided on the product packaging or visit the official RASTAR website. Keep your purchase receipt as proof of purchase.
Product Videos
No official seller videos specifically demonstrating the RASTAR 99600 1/18 Porsche 911 GT2 RS RC Car Building Kit were available at this time. Please refer to the written instructions and diagrams for guidance.
