ODK L-Shaped Desk with Sockets, LED Strips and Drawers User Manual

Introduction

Thank you for choosing the ODK L-Shaped Desk. This manual provides detailed instructions for the assembly, operation, and maintenance of your new desk. Designed for optimal workspace utilization, this desk features integrated power sockets, LED lighting, and convenient storage drawers to enhance your productivity and comfort. Please read this manual thoroughly before beginning assembly or use to ensure proper setup and safe operation.

Figure 1: Overview of the ODK L-Shaped Desk setup.

Safety Instructions

• Always assemble the desk on a soft, clean surface to prevent scratches.
• Ensure all screws and fasteners are securely tightened before use. Periodically check and re-tighten as needed.
• Do not overload the desk or its shelves. Refer to the specifications section for weight capacities.
• Keep electrical components (sockets, LED strips) away from liquids.
• Use only the provided power adapter for the LED strips and sockets.
• Keep small parts out of reach of children during assembly.
• If any parts are missing or damaged, do not proceed with assembly. Contact customer support immediately.

Package Contents

Before starting assembly, verify that all components listed below are present and undamaged. If anything is missing, please contact ODK customer service.

Setup and Assembly

Assembly typically requires two people and takes approximately 1-2 hours. Follow the steps carefully, referring to the diagrams for visual guidance.

1. Prepare Your Workspace

Clear an open area large enough to accommodate the desk's dimensions (110 x 135 x 89 cm). Lay down a blanket or cardboard to protect the desk surfaces and your floor during assembly.

Figure 2: Desk dimensions for planning your space. The desk measures 110 cm deep, 135 cm wide, and 89 cm high.

2. Assemble the Main Frame

1. Identify all metal frame components. Attach the vertical legs to the horizontal support bars using the provided screws and Allen wrench. Do not fully tighten screws until all components are loosely assembled.
2. Ensure the frame is stable and square before tightening all screws.

3. Attach Desktop Panels

1. Carefully place the desktop panels onto the assembled frame, aligning the pre-drilled holes.
2. Secure the desktop panels to the frame using the appropriate screws.

4. Install Drawers and Shelves

1. Assemble the fabric drawers according to their individual instructions.
2. Slide the assembled drawers into their designated slots within the desk frame.
3. Place any additional shelves onto their support brackets.

Figure 3: The four fabric drawers provide convenient storage for office supplies and personal items.

5. Connect Power and LED Components

1. Locate the integrated power outlet strip. Secure it to the designated area on the desk, usually underneath or on the side of the desktop.
2. Attach the LED strip lights to the underside of the monitor stand or desired location using the adhesive backing.
3. Connect the LED strip to its power adapter and then to the power outlet strip.
4. Plug the desk's main power cord into a wall outlet.

Figure 4: The built-in power strip offers 2 AC outlets and 2 USB charging ports. The RGB LED strips provide customizable lighting with 10 lighting modes and 10 color variations.

Operating Instructions

Using the Integrated Power Sockets

• The desk is equipped with 2 AC power outlets (220-250V/15A) and 2 USB charging ports (5V/2.1A).
• Simply plug your devices into the available outlets. Ensure the desk's main power cord is connected to a live wall outlet.
• Avoid plugging in high-power appliances that exceed the strip's maximum wattage.

Controlling the LED Strip Lights

• The LED strips are controlled via a remote control (if included) or a button on the LED controller.
• Power On/Off: Press the power button on the remote or controller.
• Change Color: Use the color selection buttons on the remote to choose from 10 color variations.
• Change Mode: Cycle through 10 lighting modes (e.g., static, flash, fade) using the mode button.
• Adjust Brightness: Use the brightness up/down buttons to adjust the intensity of the lights.

Utilizing the Drawers and Shelves

• The four fabric drawers are ideal for organizing documents, stationery, and other office supplies.
• The open shelves provide additional space for books, decorative items, or computer components.

Maintenance

• Cleaning: Wipe the desk surfaces with a damp cloth. For stubborn marks, use a mild, non-abrasive cleaner. Avoid harsh chemicals that may damage the finish.
• Dusting: Regularly dust the desk and its components to prevent buildup.
• Fasteners: Periodically check all screws and bolts to ensure they remain tight. Re-tighten if necessary to maintain stability.
• LED Strips: The LED strips are designed to be removable and reusable. If repositioning, ensure the surface is clean and dry for optimal adhesion.

Troubleshooting

Specifications

• Brand: ODK
• Model Number: ZJZ-TC-4D
• Color: White
• Product Dimensions (D x W x H): 110 x 135 x 89 cm
• Item Weight: 25.2 Kilograms
• Frame Material: Engineered Wood
• Top Material Type: Wood
• Special Features: Adjustable Height, Integrated Power Sockets (2 AC, 2 USB), RGB LED Strips, Fabric Drawers
• Power Outlet Specifications: 220-250V/15A (AC), 5V/2.1A (USB)
• LED Features: 10 Lighting Modes, 10 Color Variations
• Care Instructions: Wipe with Damp Cloth
• Item Shape: L-Shape
• Style: Modern
• Finish Type: Laminated

Warranty and Support

ODK stands behind the quality of its products. For information regarding warranty coverage, please refer to the warranty card included with your purchase or visit the official ODK website.

If you encounter any issues during assembly or operation, or if you have questions about your ODK L-Shaped Desk, please contact our customer support team:

• Email: support@odk.com
• Phone: +1-XXX-XXX-XXXX
• Website: www.odk.com

Please have your model number (ZJZ-TC-4D) and purchase date ready when contacting support.