GAMDIAS AURA GL240 V2 240mm AIO Liquid CPU Cooler Instruction Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your GAMDIAS AURA GL240 V2 240mm All-In-One (AIO) Liquid CPU Cooler. Please read this manual thoroughly before proceeding with installation to ensure proper setup and optimal performance.

Image: The GAMDIAS AURA GL240 V2 Liquid CPU Cooler, showcasing the radiator, two 120mm ARGB fans, and the rotatable pump housing.

Package Contents

Verify that all components listed below are present in your package:

• AURA GL240 V2 Radiator with Integrated Pump
• 2 x 120mm ARGB PWM Fans
• Universal Mounting Kit for Intel and AMD Sockets
• Thermal Paste (pre-applied or in a syringe)
• Fan Screws and Mounting Hardware
• ARGB Controller (if applicable)

Image: All components of the universal mounting kit for the AURA GL240 V2, including brackets, screws, and thermal paste.

Specifications

Compatibility

The AURA GL240 V2 Series is designed for broad compatibility with both Intel and AMD platforms. Supported CPU sockets include:

• Intel: LGA 20XX, LGA 1851, LGA 1700, LGA 1200, LGA 115X (1150, 1151, 1155, 1156)
• AMD: AM5, AM4, AM3

Image: The universal mounting kit components, illustrating compatibility with both AMD (AM5 Ready) and Intel (LGA 1700 Ready) platforms.

Installation Guide

Follow these steps carefully to install your AURA GL240 V2 liquid CPU cooler.

1. Pre-Installation

1. Prepare your Motherboard: Ensure your motherboard is removed from the PC case or has sufficient access for installation.
2. Identify CPU Socket: Determine if your CPU is Intel or AMD and select the appropriate mounting hardware from the kit.
3. Apply Thermal Paste: If thermal paste is not pre-applied to the cold plate, apply a small, pea-sized amount to the center of your CPU's Integrated Heat Spreader (IHS).

2. Radiator and Fan Installation

1. Mount Fans to Radiator: Attach the two 120mm ARGB PWM fans to the radiator using the provided fan screws. Ensure the fan airflow direction is appropriate for your case's cooling strategy (intake or exhaust).
2. Install Radiator in Case: Secure the radiator assembly to an available 240mm mounting location in your PC case (e.g., top, front, or rear). Use the appropriate screws to firmly attach it.

Image: Close-up view of the two 120mm ARGB PWM fans attached to the radiator, highlighting their design and lighting capabilities.

3. Pump Installation (Intel)

1. Install Backplate: Place the Intel backplate behind the motherboard, aligning the holes with the CPU socket.
2. Attach Stand-offs: Screw the appropriate Intel stand-offs into the backplate through the motherboard's mounting holes.
3. Mount Pump: Place the pump block onto the CPU, aligning the mounting holes with the stand-offs. Secure it with the Intel mounting brackets and thumb screws, tightening in a cross pattern until snug.

4. Pump Installation (AMD)

1. Prepare Stock Backplate: Ensure the stock AMD backplate is in place on the motherboard. Remove the plastic retention clips if present.
2. Attach Stand-offs: Screw the appropriate AMD stand-offs into the stock backplate's mounting holes.
3. Mount Pump: Place the pump block onto the CPU, aligning the mounting holes with the stand-offs. Secure it with the AMD mounting brackets and thumb screws, tightening in a cross pattern until snug.

Image: The rotatable pump housing of the AURA GL240 V2, indicating its ability to be adjusted for optimal orientation and aesthetic appeal.

5. Cable Connections

1. Pump Power: Connect the pump's 3-pin or 4-pin power cable to the CPU_FAN or AIO_PUMP header on your motherboard. Refer to your motherboard manual for the correct header.
2. Fan Power: Connect the 4-pin PWM fan cables from both fans to the CPU_FAN and/or SYS_FAN headers on your motherboard. Daisy-chaining may be an option if supported.
3. ARGB Lighting: Connect the 3-pin 5V ARGB cables from the fans and pump to a compatible 5V 3-pin ARGB header on your motherboard or to the included ARGB controller.
4. Cable Management: Utilize the hidden cable routing features of the fans and your PC case to maintain a clean and organized build.

Image: The hidden cable routing design of the fans, demonstrating how cables are managed for a neat and organized system build.

Operation

Once installed, the GAMDIAS AURA GL240 V2 operates automatically to cool your CPU. The fans and pump adjust their speed based on CPU temperature, controlled by your motherboard's PWM settings.

ARGB Lighting Control

The ARGB lighting can be controlled in two ways:

• Motherboard Sync: If connected to a 5V 3-pin ARGB header, you can synchronize the lighting effects with your motherboard's software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, ASRock Polychrome Sync, GIGABYTE RGB Fusion 2.0).
• Built-in Effects: If connected to the included ARGB controller or a case reset button, you can cycle through 30 built-in lighting effects. Refer to the controller's instructions for specific button presses.

Image: The AURA GL240 V2 installed in a PC case, showcasing its vibrant ARGB lighting and compatibility with various motherboard sync technologies.

Maintenance

Regular maintenance ensures the longevity and optimal performance of your liquid cooler.

• Dust Cleaning: Periodically clean dust from the radiator fins and fan blades using compressed air or a soft brush. Ensure fans are not spinning during cleaning.
• Inspect Tubing: Check the tubing for any signs of kinks, leaks, or damage.
• Pump Noise: Monitor the pump for unusual noises, which could indicate an issue.

Troubleshooting

If you encounter issues with your AURA GL240 V2, refer to the following common problems and solutions:

• No Power/Fans Not Spinning:
  • Check all power connections to the motherboard (CPU_FAN, AIO_PUMP, SYS_FAN headers).
  • Ensure the power supply is functioning correctly.
• High CPU Temperatures:
  • Verify the pump is running (you may feel a slight vibration or hear a low hum).
  • Ensure the cold plate is making proper contact with the CPU. Re-seat the pump if necessary, checking thermal paste application.
  • Check for obstructions in the radiator fins or fan blades.
  • Confirm fans are spinning in the correct direction for optimal airflow.
• ARGB Lighting Not Working/Flickering:
  • Ensure the 5V 3-pin ARGB cable is correctly connected to the motherboard header or controller.
  • Check your motherboard's ARGB software settings.
  • If using a controller, ensure it is powered and functioning.
• Excessive Noise:
  • Identify if the noise is coming from the fans or the pump.
  • If from fans, check for loose screws or obstructions. Adjust fan speed settings in BIOS/UEFI or software.
  • If from the pump, ensure it is mounted securely and there are no air bubbles trapped. Orient the radiator correctly (hoses down) to minimize air in the pump.

Warranty and Support

GAMDIAS products are manufactured to high-quality standards. For warranty information, please refer to the warranty card included with your product or visit the official GAMDIAS website. If you require technical assistance or have questions not covered in this manual, please contact GAMDIAS customer support through their official channels.

For further support and product registration, please visit: www.gamdias.com