oneisall BM1
Contents
oneisall BM1 Dog Grooming Vacuum Hose User Manual
Model: BM1
1. Introduction
Thank you for choosing the oneisall BM1 Dog Grooming Vacuum Hose. This manual provides essential information for the safe and effective use of your product. Please read it thoroughly before use and keep it for future reference.
2. Safety Information
Your safety and the safety of your pet are paramount. Please observe the following safety warnings:
- Do not use this product on infants or very young animals.
- Keep the hose and any connected grooming tools away from water sources to prevent electric shock.
- Exercise caution around moving parts of any connected grooming device.
- Ensure your dog is comfortable with the sound and movement of the grooming vacuum system before use. Gradual introduction is recommended.
- Inspect the hose for any damage before each use. Do not use if damaged.
- This hose is designed for use with compatible oneisall dog grooming vacuum systems only.
3. Product Overview
The oneisall BM1 Dog Grooming Vacuum Hose is an accessory designed to connect your grooming tools to a compatible oneisall vacuum dryer and clipper system, facilitating efficient pet grooming and hair collection.
Components:
- Flexible Vacuum Hose
- Connector A (for grooming tool attachment)
- Connector B (for vacuum unit attachment)

Figure 3.1: The oneisall BM1 Dog Grooming Vacuum Hose, showing its flexible design and connectors.
4. Setup
Follow these steps to set up your oneisall BM1 Vacuum Hose:
- Unpack the vacuum hose from its packaging.
- Identify the two ends of the hose. One end connects to the grooming tool, and the other to the vacuum unit.
- Connect one end of the hose securely to the designated port on your oneisall dog grooming vacuum dryer and clipper unit. Ensure it clicks into place or is firmly twisted.
- Connect the other end of the hose to your desired oneisall grooming tool (e.g., brush, clipper attachment). Ensure a secure fit.

Figure 4.1: Illustration of the BM1 hose properly connected to a compatible oneisall grooming vacuum unit and a grooming tool.
5. Operating Instructions
Once the hose is securely connected to both the vacuum unit and the grooming tool, you can begin grooming. Refer to the user manual of your specific oneisall grooming vacuum dryer and clipper for detailed operating instructions of the main unit and its tools.
- Ensure all connections are tight before turning on the vacuum unit.
- Turn on your oneisall grooming vacuum system according to its instructions.
- Proceed with grooming your pet, allowing the vacuum system to collect loose hair and debris through the hose.
6. Compatibility
The oneisall BM1 Dog Grooming Vacuum Hose is specifically designed for use with oneisall Dog Grooming Vacuum Dryers and Clippers. It is compatible with models such as oneisall B0C23PD2X3.
Important: This hose may not be compatible with other brands or specific oneisall models not listed as compatible. Always verify compatibility before attempting to connect.

Figure 6.1: The BM1 hose demonstrating non-compatibility with various other grooming vacuum models.
7. Maintenance and Care
Proper maintenance ensures the longevity and optimal performance of your vacuum hose:
- Cleaning: After each use, disconnect the hose from both the vacuum unit and the grooming tool. Gently shake out any accumulated hair or debris from inside the hose. If necessary, use a soft, dry cloth to wipe the exterior. Do not submerge the hose in water.
- Storage: Store the hose in a clean, dry place, away from direct sunlight and extreme temperatures. Avoid kinking or sharply bending the hose during storage to prevent damage.
- Inspection: Periodically inspect the hose for any signs of wear, tears, cracks, or blockages. Replace the hose if any significant damage is observed.
8. Troubleshooting
If you encounter issues with your oneisall BM1 Vacuum Hose, consider the following:
| Problem | Possible Cause | Solution |
|---|---|---|
| Reduced suction through hose | Hose blockage (hair, debris) | Disconnect hose and clear any obstructions. |
| Hose detaches during use | Improper connection | Ensure hose is securely attached to both the vacuum unit and the grooming tool. |
| Hose appears damaged | Physical wear or tear | Discontinue use and replace the hose. |
For issues not listed here, please contact oneisall customer support.
9. Specifications
| Feature | Detail |
|---|---|
| Model Name | BM1 |
| Brand | oneisall |
| Manufacturer Reference | PJ24027 |
| Product Dimensions | 32.2 x 19.5 x 6.5 cm (packaged) |
| Item Weight | 340 grams |
| Recommended Use | Dog grooming vacuum hose for clipping and grooming |
| Special Feature | Designed for vacuum system integration |
| Target Audience | Dogs |
10. Warranty and Support
For warranty information or technical support, please refer to the documentation included with your oneisall grooming vacuum system or visit the official oneisall website. Keep your purchase receipt as proof of purchase.
For further assistance, you may contact oneisall customer service through their official channels.
Documents and downloads
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.