Anderic DC8-96SG8 Ceiling Fan Receiver Replacement Instruction Manual

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of the Anderic DC8-96SG8 Ceiling Fan Receiver. This receiver is designed as a direct replacement for specific 6-speed DC motor ceiling fans that originally utilized a DC8 series receiver. Please read this manual thoroughly before installation and use to ensure proper function and safety.

2. Product Overview

The Anderic DC8-96SG8 is a high-quality replacement receiver for 6-speed DC motor ceiling fans. It restores all original fan functions, including:

• 6-speed fan control.
• Reverse airflow for seasonal comfort.
• LED light dimming support up to 60W.

The motor output is rated up to 40W, ensuring efficient and consistent performance.

Figure 1: Front view of the Anderic DC8-96SG8 Ceiling Fan Receiver, showing the compact black unit with various colored wires extending from both ends for connection to the fan and power supply.

3. Compatibility

This receiver is designed for specific ceiling fan models. It is compatible with select models from the following brands that originally used a DC8 series receiver:

• Monte Carlo
• Casa Vieja
• Hampton Bay

Important: This product is not universal. It is not compatible with Minka Aire, Hunter, or other proprietary systems. Always confirm your existing receiver is labeled "DC8" before purchasing to ensure a proper match. This receiver will not function in fans that were not originally equipped with a DC8 receiver.

4. Package Contents

The package includes:

• 1x Anderic DC8-96SG8 Ceiling Fan Receiver

Note: The Anderic DC1 remote control, which is required for operation, is sold separately. If both a transmitter and receiver are needed, consider the Anderic DC1/DC8 Kit for a complete solution.

5. Safety Information

Please observe the following safety precautions:

• Disconnect Power: Always turn off power to the ceiling fan at the main circuit breaker before attempting any installation, wiring, or maintenance.
• Qualified Electrician: For best results and safety, professional installation by a qualified electrician is recommended.
• Correct Wiring: Ensure all wiring connections are secure and comply with local electrical codes.
• Voltage: Verify that the power supply voltage matches the receiver's requirements (AC 120V/60Hz).
• Weight Support: Ensure the ceiling fan mounting structure can support the weight of the fan and receiver.

6. Setup and Installation

6.1. Wiring Diagram

Figure 2: Back view of the Anderic DC8-96SG8 Ceiling Fan Receiver, displaying the wiring diagram and product specifications. The diagram illustrates connections for AC power, fan motor (Moteur 1, 2, 3), and light (For Light).

Refer to the wiring diagram printed on the back of the receiver (Figure 2) and the existing wiring of your ceiling fan for correct connections. The diagram typically shows connections for:

• AC IN: Live (L) and Neutral (N) power supply.
• FOR LIGHT: Light fixture connection.
• MOTOR: Fan motor connections (often labeled Moteur 1, Moteur 2, Moteur 3 for multi-speed DC motors).
• ANTENNA: For remote signal reception.

6.2. Installation Steps (General)

1. Power Disconnection: Turn off power to the ceiling fan at the main circuit breaker.
2. Access Receiver: Carefully lower the fan canopy to access the existing receiver and wiring.
3. Remove Old Receiver: Disconnect the old receiver, noting all wire connections. It is advisable to take photos for reference.
4. Install New Receiver: Connect the Anderic DC8-96SG8 receiver according to the wiring diagram (Figure 2) and your fan's specific wiring. Ensure all connections are secure using wire nuts.
5. Position Receiver: Carefully place the new receiver within the fan canopy, ensuring no wires are pinched.
6. Restore Power: Restore power at the circuit breaker.

6.3. Pairing with DC1 Remote Control

After installation, the receiver must be paired with an Anderic DC1 remote control (sold separately) to function. The pairing procedure typically involves:

1. Ensure power is supplied to the fan.
2. Within a short timeframe (usually 30-60 seconds) of restoring power, press and hold the "LEARN" or "PAIR" button on your Anderic DC1 remote control. Refer to your DC1 remote's manual for the exact button and procedure.
3. The fan light may blink or the fan may briefly turn on to indicate successful pairing.

If pairing fails, repeat the steps. Ensure the remote has fresh batteries and is within range.

Figure 3: Side view of the Anderic DC8-96SG8 Ceiling Fan Receiver, showing the model number label "DC8-96SG8-L-D" and the antenna wire.

7. Operating Instructions

Once the Anderic DC8-96SG8 receiver is successfully installed and paired with the DC1 remote control, you can operate your ceiling fan using the remote. Functions typically include:

• Fan Speed Control: Adjust between 6 fan speeds.
• Fan On/Off: Turn the fan on or off.
• Reverse Airflow: Change the direction of fan rotation for summer (downward airflow) or winter (upward airflow) operation.
• Light On/Off: Turn the fan light on or off.
• Light Dimming: Adjust the brightness of compatible LED lights (up to 60W).

Refer to your Anderic DC1 remote control manual for specific button functions and detailed operating instructions.

8. Maintenance

The Anderic DC8-96SG8 receiver is designed for long-lasting reliability and requires minimal maintenance.

• Cleaning: Ensure the area around the receiver within the fan canopy remains free of dust and debris. Do not use liquid cleaners directly on the receiver.
• No User-Serviceable Parts: The receiver contains no user-serviceable parts. Do not attempt to open or repair the unit.
• Regular Checks: Periodically check the fan's operation to ensure all functions are working correctly.

9. Troubleshooting

If troubleshooting steps do not resolve the issue, contact Anderic customer support for further assistance.

10. Specifications

11. Warranty and Support

For warranty information or technical support, please contact Anderic customer service. Details regarding specific warranty periods and terms are typically provided with the product packaging or on the manufacturer's official website.

Manufacturer: Dan's Electronics Etc., Inc.