SOCAL-LED LIGHTING Xenon HID Headlight Ballast and D1S 6000K Bulb Instruction Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your SOCAL-LED LIGHTING Xenon HID Headlight Ballast with Igniter and D1S 6000K Bulb. This product is designed as a direct OEM replacement, offering a plug-and-play solution that meets or exceeds original equipment specifications.

Package Contents:

• 1 x D1S 6000K HID Bulb
• 1 x HID Ballast with Igniter
• 1 x Connection Cable

Image 1: Overview of the SOCAL-LED LIGHTING HID Headlight Ballast, Igniter, and D1S Bulb.

2. Vehicle Compatibility and OEM Part Numbers

This HID Headlight Ballast and Bulb kit is compatible with various vehicle models. Please verify your vehicle's specific requirements before installation.

Compatible Vehicle Models:

• 2007-2009 Audi Q7
• 2008-2013 BMW 1-series (Coupe and Convertible)
• 2008-2012 Buick Enclave
• 2007-2012 GMC Acadia
• 2008-2013 Jeep Grand Cherokee
• 2006-2012 Jeep Commander
• 2009-2012 Mitsubishi Eclipse
• 2007-2009 Volvo S60
• 2010-2013 Volvo XC60

Replaces OEM Part Numbers:

• 89034934
• 043731 6G
• 93186542
• 30784923
• 6224L8, 6224.L8, 6224-L8
• 4L0 907 391 A, 4L0907391
• 4L0 907 391A, 4L0907391A
• 7701208945
• 63117180050, 63 11 7 180 050, 7180050
• 89076976
• 89032336
• 4L0 907 391, 4L090739

Important Notice:

Please verify that your factory ballast and connectors exactly match the product shown in the images before placing an order. Some manufacturers may change the ballast type during mid-cycle refreshes or new production dates.

Image 2: Detailed view of the ballast connector for verification.

3. Setup and Installation

Installation of the Xenon HID Headlight Ballast and D1S Bulb requires careful handling. It is recommended to consult your vehicle's specific service manual or seek professional assistance if you are not familiar with automotive electrical systems.

General Installation Steps:

1. Safety First: Ensure the vehicle's ignition is off and the battery is disconnected before beginning any electrical work.
2. Access Headlight Assembly: Depending on your vehicle model, you may need to remove the headlight assembly to access the bulb and ballast.
3. Disconnect Old Components: Carefully disconnect the wiring from the old ballast and bulb.
4. Remove Old Bulb: Turn the old D1S bulb counter-clockwise to loosen and remove it from the headlight housing.
5. Prepare New Bulb: If necessary, install the plastic retainer clip onto the new D1S bulb and connect the igniter cable.
6. Install New Bulb: Insert the new D1S bulb into the headlight housing and turn it clockwise to secure it.
7. Connect New Ballast: Connect the igniter cable from the bulb to the new ballast. Then, connect the vehicle's power connector to the new ballast.
8. Secure Components: Ensure all components are securely mounted and wiring is routed safely, away from moving parts or heat sources.
9. Test Functionality: Reconnect the battery and test the headlight functionality before reassembling the vehicle.

Image 3: Components connected, ready for installation.

4. Operating Instructions

The SOCAL-LED LIGHTING Xenon HID Headlight Ballast and D1S Bulb operate as a plug-and-play system. Once correctly installed and connected to your vehicle's electrical system, the headlights will activate when the vehicle's lighting system is turned on.

Key Features:

• Color Temperature: 6000 Kelvin (Crystal White)
• Brightness: Approximately 3500 Lumens, providing enhanced visibility.
• Fast Startup: Designed for quick illumination.

Image 4: Illustration of high brightness output and clear beam pattern provided by HID lights.

Image 5: Visual comparison demonstrating improved road illumination with HID headlights.

5. Maintenance

These HID components are designed for durability and long-term performance with minimal maintenance. However, proper care can extend their lifespan.

General Care:

• Keep headlight assemblies clean from dirt and debris.
• Avoid touching the glass part of the D1S bulb directly with bare hands, as oils can reduce bulb life. Use gloves during installation.

Warning:

The most common reason for ballast failure is water ingress into the headlight assembly. If your headlight has water inside and your ballast has failed due to this, you may need to replace the entire headlight assembly, as a replacement ballast will likely fail again under the same conditions.

6. Troubleshooting

If you experience issues with your HID headlight system, consider the following common problems and solutions:

Common Issues:

• Headlight Not Turning On:
  • Check all electrical connections to ensure they are secure and properly seated.
  • Verify the vehicle's fuse for the headlight circuit.
  • Ensure the ballast is receiving power.
• Headlight Flickering or Dimness:
  • This can indicate a failing ballast or bulb. Try swapping components with the working side (if applicable) to isolate the issue.
  • Check for stable voltage supply to the ballast.
• Headlight Stays On or Does Not Turn Off:
  • This is often a sign of a faulty ballast or a wiring issue. Disconnect the battery or pull the fuse to turn off the light.
  • Consult a qualified mechanic for diagnosis.
• Incompatibility Issues:
  • Double-check the OEM part numbers and vehicle compatibility list. Some vehicles may have specific electrical requirements or variations.

If troubleshooting steps do not resolve the issue, please contact customer support.

7. Specifications

8. Warranty

SOCAL-LED LIGHTING products are manufactured to high-quality standards. This product is covered by a limited warranty against manufacturing defects. For specific warranty terms and conditions, please refer to the product packaging or contact customer support.

9. Customer Support

For further assistance, technical support, or warranty claims, please contact SOCAL-LED LIGHTING customer service through the retailer where the product was purchased or visit the official SOCAL-LED LIGHTING store online.

Visit the SOCAL-LED LIGHTING Store