ZIPRO Core Foldable Multi-purpose Weight Bench Instruction Manual

1. Introduction

Thank you for choosing the ZIPRO Core Foldable Multi-purpose Weight Bench. This manual provides essential information for the safe and effective assembly, operation, and maintenance of your new fitness equipment. Please read this manual thoroughly before use and keep it for future reference.

Figure 1.1: The ZIPRO Core Foldable Multi-purpose Weight Bench in its assembled state.

2. Safety Information

Your safety is paramount. Adhere to the following safety guidelines at all times:

• Consult a physician before starting any new exercise program.
• Ensure all bolts, nuts, and other connections are securely tightened before each use. Regularly check for loose parts.
• Place the bench on a flat, stable, and non-slip surface. Ensure adequate clear space around the bench for safe operation.
• Do not exceed the maximum weight capacities:
  • Total maximum load capacity: 230 kg
  • Maximum user weight: 120 kg
  • Maximum bar support capacity: 180 kg
• Keep children and pets away from the equipment during use.
• Do not modify the equipment. Use only original replacement parts if needed.
• Stop exercising immediately if you feel pain, dizziness, or nausea.
• Wear appropriate athletic footwear and clothing during workouts.

Figure 2.1: Illustration of the bench's robust design and weight capacities.

3. Package Contents

Upon opening the package, verify that all components are present and undamaged. If any parts are missing or damaged, do not proceed with assembly and contact customer support immediately.

The package should contain all necessary structural components, hardware (bolts, nuts, washers), and tools required for assembly.

4. Assembly and Setup

Follow these general steps for assembly. Refer to the included assembly diagram for detailed instructions specific to your model.

1. Unpack all components and lay them out on a clean, flat surface.
2. Identify all parts against the parts list in your assembly diagram.
3. Begin by attaching the main support frames. Ensure all connections are aligned correctly before tightening.
4. Secure the bench pad to the main frame.
5. Install the adjustable bar supports and push-up handles. Ensure they slide smoothly and lock securely into place.
6. Attach the non-slip feet to the base of the bench and support frames.
7. Once fully assembled, double-check all bolts and nuts to ensure they are securely tightened.

Figure 4.1: Key assembly points including the folding pin, adjustment knob, and stable feet.

Figure 4.2: The bench in its folded position, demonstrating space-saving design.

5. Operating Instructions

The ZIPRO Core bench offers versatility for various strength training exercises. Familiarize yourself with its adjustment mechanisms:

5.1. Bench Adjustments

• Bench Pad Position: The bench pad can be adjusted to two positions: flat and negative incline. To adjust, locate the adjustment pin or lever beneath the bench pad, pull it out, set the desired angle, and ensure the pin locks securely into place.
• Bar Support Height: The bar supports can be adjusted to seven different heights, ranging from 70 cm to 105 cm from the ground. To adjust, loosen the knob on the support upright, pull the adjustment pin, slide the support to the desired height, and re-secure the pin and tighten the knob.

Figure 5.1: The bench adjusted to an inclined position for various exercises.

Figure 5.2: Close-up of the adjustable bar supports and integrated push-up handles.

5.2. Exercise Examples

The ZIPRO Core bench is suitable for a wide range of exercises, including but not limited to:

• Bench Press: Use the adjustable bar supports for barbell exercises.
• Dumbbell Exercises: Perform chest presses, flyes, rows, and bicep curls.
• Abdominal Exercises: Utilize the negative incline position for crunches and sit-ups.
• Push-ups/Dips: Use the integrated handles for bodyweight exercises.

Figure 5.3: User demonstrating a barbell bench press exercise.

Figure 5.4: Various exercises possible with the ZIPRO Core bench, including abdominal work and dumbbell rows.

6. Maintenance

Regular maintenance ensures the longevity and safe operation of your ZIPRO Core bench:

• Cleaning: Wipe down the bench pad and frame with a damp cloth after each use to remove sweat and dirt. Use mild soap if necessary, but avoid harsh chemicals.
• Inspection: Periodically inspect all moving parts, bolts, and welds for signs of wear, damage, or loosening. Tighten any loose connections immediately.
• Storage: When not in use, the bench can be folded for compact storage. Store it in a dry place, away from direct sunlight and extreme temperatures.

Figure 6.1: Dimensions of the bench, useful for planning storage space.

7. Troubleshooting

If you encounter issues with your ZIPRO Core bench, refer to the following common solutions:

8. Specifications

Figure 8.1: Detail of the sturdy metal frame construction.

9. Warranty and Support

ZIPRO products are manufactured to high-quality standards. For information regarding warranty coverage, returns, or technical support, please refer to the warranty card included with your product or visit the official ZIPRO website. You may also contact the seller directly for assistance.

For customer service inquiries, please have your model number (11926649) and purchase date ready.