1. Introduction
Thank you for choosing the Nania ALPHA i-Size R129 Belted Booster Seat. This manual provides essential information for the correct installation, use, and maintenance of your booster seat. Please read these instructions carefully before use and keep them in a safe place for future reference.
The Nania ALPHA booster seat is designed and tested in France, ensuring compliance with high safety standards. It is approved according to the latest i-Size R129 safety standard, suitable for children between 126 cm and 150 cm in height.

Image: Front view of the Nania ALPHA i-Size R129 Belted Booster Seat in Flamingo color.
2. Safety Information and Warnings
- Always ensure the booster seat is correctly installed and the child is properly secured before every journey.
- This booster seat is designed for forward-facing use only.
- The child must be secured using the vehicle's 3-point seat belt.
- Never leave a child unattended in the booster seat.
- Do not use the booster seat if it has been involved in an accident, even if there is no visible damage. Internal damage may compromise its safety.
- Do not modify the booster seat or use accessories not approved by the manufacturer.
- Ensure the vehicle's seat belt is not twisted and lies flat across the child's body, over the shoulder and across the hips.
3. Product Components
The Nania ALPHA booster seat consists of a lightweight yet sturdy shell made from EPP (Expanded Polypropylene) and polyester fabric covers. It features integrated armrests for enhanced comfort.

Image: Close-up view showing the lightweight and sturdy EPP shell material of the booster seat.

Image: Detail showing the integrated armrests designed for child comfort.
4. Installation
The Nania ALPHA booster seat is installed using the vehicle's 3-point seat belt system. It is designed for forward-facing use on a vehicle seat equipped with a 3-point lap and shoulder belt.
- Place the booster seat firmly on the vehicle's rear seat. Ensure it is stable and does not wobble.
- Seat the child in the booster seat.
- Pull the vehicle's 3-point seat belt over the child and the booster seat.
- Guide the lap portion of the seat belt under the armrests and across the child's hips, ensuring it sits low on the hips and not across the stomach.
- Guide the shoulder portion of the seat belt through the belt guide (if present) or ensure it rests comfortably across the child's shoulder, away from the neck, and across the chest.
- Buckle the seat belt securely.
- Pull the shoulder belt to remove any slack, ensuring a snug fit without being too tight.

Image: A child being seated and secured in the Nania ALPHA booster seat using the vehicle's 3-point seat belt.
5. Operating Instructions (Child Securing)
Once the booster seat is correctly positioned in the vehicle, securing your child is a straightforward process:
- Ensure the child is sitting upright and fully against the back of the booster seat.
- Fasten the vehicle's 3-point seat belt.
- Check that the lap belt is positioned low across the child's hips, touching the thighs.
- Verify that the shoulder belt crosses the center of the child's shoulder and chest, not touching the neck or sliding off the shoulder.
- Tighten the seat belt to remove any slack, ensuring a secure fit. The belt should be snug but not uncomfortable for the child.
6. Care and Maintenance
Proper care and maintenance will extend the life of your Nania ALPHA booster seat.
Cleaning Instructions:
- The fabric cover can be removed for cleaning. Refer to the care label on the cover for specific washing instructions. Typically, machine wash on a gentle cycle with mild detergent and cold water. Do not bleach.
- Allow the cover to air dry completely before reattaching it to the booster seat. Do not tumble dry.
- The plastic parts of the booster seat can be wiped clean with a damp cloth and mild soap. Do not use abrasive cleaners or solvents.
- Do not lubricate any parts of the booster seat.
Storage:
When not in use, store the booster seat in a cool, dry place away from direct sunlight.
7. Troubleshooting
If you encounter any issues with your Nania ALPHA booster seat, please review the following common concerns:
- Booster seat feels loose: Ensure the vehicle's 3-point seat belt is properly routed and tightened. The booster seat should be stable on the vehicle seat.
- Seat belt is twisted or not lying flat: Unbuckle the seat belt, straighten it, and re-route it carefully, ensuring it lies flat across the child's body and the booster seat.
- Child is uncomfortable: Ensure the child meets the minimum height requirement (126 cm) for this booster seat. Check that the seat belt is not too tight or rubbing against the child's neck. Adjust the child's seating position if necessary.
- Missing parts: Contact customer support immediately if any parts are missing upon unboxing. Do not use the booster seat if it is incomplete.
For issues not covered here, please refer to the support section.
8. Specifications
| Feature | Specification |
|---|---|
| Model Name | ALPHA |
| Manufacturer Reference | 2139110257A |
| Safety Standard | i-Size R129 |
| Minimum Recommended Height | 126 cm |
| Maximum Recommended Height | 150 cm |
| Maximum Supported Weight | 40 kg |
| Orientation | Forward-facing |
| Harness Type | 3-point (vehicle belt) |
| Main Material | Plastic (EPP) |
| Composition | Polyester and EPP |
| Product Dimensions (L x W x H) | 36 x 45 x 22 cm |
| Product Weight | 1 kg |
| Batteries Required | No |
| Manufacturing Location | France |

Image: Technical diagram illustrating the dimensions (length, width, height) and weight of the Nania ALPHA booster seat.
9. Warranty and Support
Nania products are manufactured to high-quality standards. For specific warranty information, please refer to the documentation provided at the time of purchase or contact your retailer.
For technical support, spare parts, or any questions regarding your Nania ALPHA booster seat, please contact Nania customer service through their official website or your point of purchase. Please have your model number (2139110257A) and purchase date ready when contacting support.